The figure below shows a steel structure made up of two pre-assembled segments that are hoisted by a mobile crane using a bespoke lifting frame. Each cable must withstand loads of FAB = FAC = FAD = FAE = 4000 kN. You must provide an accurate answer in scientific standard form with one decimal place only. In cartesian vector and in scalar form, compute the rAB, rAC, TAD & rAE length. 14 m 6m 6 m в 3 m 3 m X

The figure below shows a steel structure made up of two pre-assembled segments that are hoisted by a mobile crane using a bespoke lifting frame. Each cable must withstand loads of FAB = FAC = FAD = FAE = 4000 kN. You must provide an accurate answer in scientific standard form with one decimal place only. In cartesian vector and in scalar form, compute the rAB, rAC, TAD & rAE length. 14 m 6m 6 m в 3 m 3 m X

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.73P

See similar textbooks

Similar questions

In your response, please display the full computation and all FBDs that were used. Only round off at the final answer with 4 decimal places. P=2kN, F=3kN, and moment M=0.5kN-m are acting on the structure in the illustration. A pin at Z and a cable RQ connected by a connecting pin R support it. Im ● F ● P S TO M Im R lu W OZ a' 0.8m 3m If the pin support Z's factor of safety against shear stress is 3, determine whether a single or double shear should be provided for an economical and safe design. 4 m The mas allowable shear stress in the pin is 50MPa. Consider the following specifications. Single shear design: 25mm pin diameter Double shear design: 17mm pin diameter
! Required information A rope connecting points A and B supports the force Fshown in the figure. Write expressions using Cartesian vector representation for the following. Take L = 8 ft and F= 12 Ib. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. y B 30° ÜBA : the unit vector from B to A. ÜBA
S00 Ib In the fig. shown, compute the ff: (16-18) the resultant using cosine law (force polygon) 60 R = 35 (19-20) the angle of the R measured 500 lb cW from the x- axis.
Required information A rope connecting points A and B supports the force Fshown in the figure. Write expressions using Cartesian vector representation for the following. Take L 8 ft and F 12 lb, Part 2 of 6 NOTE: This is a multi-part question, Once an answer is submitted, you will be unable to return to this part. 10 points y eBook B T 30° Hint F Print References T BA : the position vector from B to A. Mc Graw Hill MacBook Air
In picking up a load from position B, a cable tension T of magnitude 24 kN is developed in on the construction crane cable as shown. 18 m A. TY 30 m 5 m 6 m Compute the magnitude of the Position Vector RAB = Rxi + R„j+ Rzk (Answers in m) Answer: Type here to search
The following diagram corresponds to questions 1 to 3. A beam rests on two sharp edges as shown on the image. The beam has a length of 7,50 m and a mass of 4,25 kg. Object 1 has a mass of 1,50 kg; object 2 has a mass of 2,35 kg. Point P is 0,50 m form the center of the beam. CG 1. How much is the torque done by object 1 around point P? A. 55,2 N*m B. 7,36 N*m C. 62,5 N*m D. Object 1 doesn't exert a torque. 2. How much is the torque done by the force of gravity of the beam around point P? A. 20,8 N*m N-m ך177 .B C. 156 N*m D. 313 N*m 3. If you needed to cancel the nomal forces of the two objects, where you should place object 2? The axis of rotation is point P. A. 3,30 m from point B. 9,18 m from point P C. 5,69 m from point P D. 3,62 m from point P
The following diagram corresponds to questions 1 to 3. A beam rests on two sharp edges as shown on the image. The beam has a length of 7,50 m and a mass of 4,25 kg. Object 1 has a mass of 1,50 kg; object 2 has a mass of 2,35 kg. Point P is 0,50 m form the center of the beam. d 2 Pl CG 1. How much is the torque done by object 1 around point P? A. 55,2 N*m B. 7,36 N*m С. 62,5 N*m D. Object 1 doesn't exert a torque.
Help Save & Exit Check Required information A rope connecting points A and B supports the force Fshown in the figure. Write expressions using Cartesian vector representation for the following. Take L= 8 ft and F= 12 lb. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. B 30° F T AB : the position vector from A to B. TAB of 17 Next > < Prev 6. 9. 41
GIVEN : W= 345 N Q°= 27 DEGREE R°= 50 DEGREE S°= 25 DEGREE SOLVE (a) AC= IN NEWTON SOLVE (b) BC= IN NEWTON SOLVE (c) CD= IN NEWTON PLS PLS SHOWS THE COMPLETE SOLUTION AND WRITES LEGIBLY AND ALSO INCLUDES THE FREE-BODY DIAGRAM. WRITE IN FOUR DECIMAL PLACES. TAKE NOTE : USE EQUILIBRIUM NOT LAMI'S THEOREM
Graphical Method : Polygon Method F1 - 150N, 30° N of E F2 - 100N, 60° E of S 1) Find the Length and Angle 2) Find Resultant Force Vector Magnitude and %Error 3) Find Resultant Force Vector Direction and %Error
a = 1.2 m b = 1.8 m c = 4 m Force AB - 500 Newtons B FAB Find the Length of AB in m. If the calculated answer is not whole number, express it in 4 significant figures. If the value is negative, include a negative sign. Find the x-component of unit vector AB. (Hint: the value should be less than 1). Find the y-component of unit vector AB. (Hint: the value should be less than 1).
In the figure, let the mass of the block be 8.50 kg and the angle 0 = 30.0⁰ Step 1 m Create the free-body diagram. Use the checkboxes to select the correct vectors as instructed above. Move the vectors to the correct starting points and orient them in the correct direction as instructed. FN mg Frictionless T Draw free-body diagram here :+y +x Key to Force Labels FN = Normal force mg Gravitational force ƒ= Frictional force T = Tension