The beam in Fig 5-1. is used to support a dead load(self weight of 0.8 kN/m, a live load 4 kN/m, and concentrated live loudof 20 kN/m1- Draw the influnce for Shear at C (vc) [use Muller preslau'smethod,2- Determine (a) the maximum negative shear at c. Assume Band Dare hings and E is an interval hinge,|--4mCIB4nETD

Answered: Image /qna-images/answer/e0cb6c40-637a-4067-ba64-0b6b23c16320.jpg

Answered: The beam in Fig 5-1. is used to support…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is supported by bolts at A and B that are in the single shear. The bar is loaded by 4kn at point D. Determine the minimum diameter of the bolt at B if the allowable shear stress is 120 mpA
A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is supported by bolts at A and B that are in the single shear. The bar is loaded by 4kn at point D. Dtermine the resultant action at B
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the deformation at wire BD. E 4 m +2m+2m -3 m O 0.417mm O 0.497mm O 0.329mm O 0.231mm
F14-11. Determine the principal stresses at point A on the cross section of the beam at section a-a. -300 mm- IT 150 mm S0 mm 30 kN 30 mm
F8-4. Determine the magnitude of the load P that will cause a maximum normal stress of max = 30 ksi in the link along section a-a. - 2 in.- E- a a 0.5 in. 2 in. T F8-4
Q2: the three forces which act on the bent bar at the support point A. Then determine the distance of action of the stand-alone resultant force R. 10KN -1.2m 4.8kN E -0.9m sts of sonation the beam caused by the pin Fosn 3.2kN
The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b = 0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi.
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that Es = 200 GPa and E,= 100 GPa, determine (a) the reactions at A and E, (b) the stress at segment BC, (c) the deflection of point D. Dimensions in mm 100 100 -180- -120- A Cl Dl E Steel B Brass 60 kN 40 kN 40-mm diam. 30-mm diam.
fong has a cross-sectionaf fa3 cm?. The rodis now hung by one a sso kgm hung from the rod's Lower Determine the stress, the strain, a nd. theelongatian of the hod.(Y=20x10 Pa)- EX. A steel rod 2 m end from a support structure and fa P ali mailling machine is end
Part 4a)Determine the reaction (in N) at the hinge at C.b) Determine the diameter of the pin at C in mm.c) Determine the corresponding bearing stress in the pedal at C in MPa.
PLEASE DRAW AND LABEL PROPERLY THE FBD. THANK YOU. From the frame loaded as shown. Solve the following: a. Reaction at column A.b. Moment at column A.c. Force at member GH.d. Force at member FE.e. Force at memeber FH.
Q-1 Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa.c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS