Q1. The three concurrent forces acting on the screw eye produce a resultant force F2= 0.8 F, and F, is to be 90° from F2 as shown. Determine the required magnitude of F3 expressed in terms of F1 and the angle 0. FR = 0. If F1 60 30 F2 F3

Q1. The three concurrent forces acting on the screw eye produce a resultant force F2= 0.8 F, and F, is to be 90° from F2 as shown. Determine the required magnitude of F3 expressed in terms of F1 and the angle 0. FR = 0. If F1 60 30 F2 F3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Analyze the loaded frame as shown. Be guided as follows: a. Solve for the reactions at supports b.…

A: Given A frame Required Solve for the reactions at supports Draw Shear and Moment Diagrams Compute…

Q: Determine the resultant reaction in D in kN using slope deflection method or moment distribution…

Q: Determine the magnitude and direction of theresultant force, measured counterclockwise from the…

A: Consider the following free body diagram of the resultant force : Consider the following free body…

Q: A uniform bar AB is resting in a horizontal position on smooth inclines as shown below. Determine…

Q: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical…

Q: The force of magnitude Facts along the edge of the triangular plate. Determine the moment of F about…

Q: Q2: The 300 N force as shown in figure acts on the point O. Resolve this force into two components…

A: Let us first find all the angles

Q: 7.4 The two homogeneous bars AB and BC are connected with a pin at B and placed between rough…

Q: Determine the slope and deflection at point B of the steel beam

Q: Question 1: a) Use Slope Deflection Method, determine the moment that each member exerts on the…

Q: Calculate the vertical reaction at B. Let P = 14 kips and W = 2 kips/ft %3D Assume A is a roller and…

A: To find the vertical reaction at B-

Q: The force of magnitude F = 181 lb acts along the edge of the triangular plate. Determine the moment…

A: moment about any point M0→ = r→x F→ or distance X perpendicular component of force

Q: 10. If Ø = 45°, F1 = 5KN , and the resultant force is 6 kN directed along the positive y axis,…

Q: 8-67. Determine the smallest horizontal force P required to lift the 100-kg cylinder. The…

Q: Block A supports a pipe column and rests as shown on wedge B. Knowing that the coefficient of static…

Q: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical…

Q: The horizontal force P = 64 N is applied to the upper block with the system initially stationary.…

A: Given that, P = 64 N mA = 18 kg mB = 7 kg μ1=0.29 μ2=0.5

Q: (a) Compute the horizontal displacement of joint B produced by the 240-kN load in Figure P8.10. For…

A: Resultant Force: The force which represents the total forces acting on the truss or any member. This…

Q: a) If the beam AD is loaded as shown in Figure Q4(a), determine the horizontal force P which must be…

A: Determine horizontal force P?

Q: Using Three-Moment Equation, determine the Reactions and defiection at point B. E-29,000 ksi and…

Q: H V b a-The internal shear force V at a certain section of a beam is 60 kN.m. If the beam has a…

Q: If the resultant (single equivalent force) of the two forces and couple M passes through point O,…

Q: H.W.3: For the beam shown in Figure El = 100,000 kip-ft² and use discontinuity functions to…

A: Continuous beam: If more than two supports are provided to the beam, it is called a continuous beam.…

Q: An equilateral triangular plate of side 2.4m placed horizontally in a liquid (SG=0.80) in such a way…

A: side of the platea=2.4marea of the equilateral triangular plateA=34side2A=342.42A=2.494 m2

Q: Determine the moment at A and D using Slope Deflection Method. Assume the supports at A and D are…

Q: Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa , a1=a2=…

A: Given:-A1=A2=900 mm2E1=E2=100GPah=1200 mmθ=60 degreeα1=α2=12*10-6/oC△T=35oCTo find:-Displacement at…

Q: Please solve using 3 kip instead of 2 kip for the downward force 2 kip at P a 60° 1 kip The end of a…

Q: If the beam AD is loaded as shown, determine the horizontal force P which must be applied to the…

A: Given :

Q: Determine the moment of this figure P1=35kN and P2=55kN

A: Given- force values-P1=35 kNP2=55 kNIt is required to determine the moment

Q: Determine the support reaction at D using Conjugate Beam Method. Indicate the negative sign if the…

A: Solution: Given Data; E=200 GPaI=300×106 mm4

Q: The speed of water passing through the elbow on a buried pipe is V = 8 ft/s. Assume water is ideal…

A: Linear Momentum: The product of mass and velocity of the fluid is known as the linear momentum of…

Q: Problem 1 Determine the tangential and normal componet of the force F=150.60 kN with respect to the…

Q: The two forces F1 and F2 acting at A have a resultantforce of FR = {-100k} lb. Determine the…

A: Given:- F1=60 lb FR=-100k To find:- F2-magnitude and direction

Q: Determine the vertical movement at C, if (P=100 kN). Steel L= 2 m A = 300 mm E = 200 GPa 3 m 2 m B…

Q: Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical…

Q: Determine force P required to be applied on the block of weight W for 5 seconds for it to reach a…

A: Using impulse momentum principle

Q: If F-30 lb and F-40 lb, determine the angles # ana e so that the resultant force is directed along…

Q: F3 45° 3 30° F1 F2 1. Determine the magnitude of the resultant force (N) 2. Determine its direction…

A: Given data in question Forces Angles To find out Resultant Direction of Resultant

Q: QT: It is required that the resultant force acting on the evebolt in the Figure to be dirccted along…

A: Given: F1=800N F2 have to be of minimum magnitude To Find: Magnitude, Angle and Resultant Force

Q: Two forces F1 and F2 act on the screw eye. If theirlines of action are at an angle θ apart and the…

A: Given: To design logic circuits to convert the 4221 codewords to BCD codewords. a. Fill in the…

Q: Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical…

Q: PROBLEM 12.70 Pin B weighs 4 oz and is free to slide in a horizontal plane along the rotating arm 0C…

A: To find radial and transverse component of reaction at B and value of P and Q

Q: o T ☺ t Q6) Compute the vertical displacement of joint B of the structure shown in the figure. 100…

Q: The horizontal force P = 64 N is applied to the upper block with the system initially stationary.…

Q: X kN -2 m→ Am 2 m Y kN B Bm D= 30+A degrees 26. What is the vertical component of the inclined load…

Q: The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for…

A: Calculation Of angle of friction θ:- μ=tanθ⇒0.268=tanθ⇒θ=tan-10.268⇒θ=15°…

Q: Determine the smallest force P subjected at the wedge B that is required to lift the B Newton crate…

A: Given, B=465 N μ=22÷100=0.22 H=12 We need to find out P.

Q: Q.2 Determine the vertical movement at C, if (P-100 kN). Steel L= 2 m A = 300 mm? E = 200 GPa C 3 m…

Q: A 0.25-kg hollow square thin plate is pin-connected to a wall with an outer side length of c = 15 cm…

Concept explainers

Graphical Methods

The graphical method is a method of solving equations involving more than one variable using the Cartesian coordinate system. In civil engineering, the use of the graphical method is limited to the problems involving two variables. The graphical method has a great impact in solving the questions regarding engineering mechanics.

Question

Q1. The three concurrent forces acting on the screw eye produce a resultant force
F2= 0.8 F, and F, is to be 90° from F2 as shown. Determine the required magnitude of F3 expressed
in terms of F1 and the angle 0.
FR = 0. If
F1
60
30°
F2
F3

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2/ The t-component of the force F is known to be 97 N. Determine the n-component and the magnitude of F. F 10° 30
If the force vector F=(33i-45j+53k) N. a=4 m; b=3 m; C3D2 m; b> a C a. a F 4a) Determine the magnitude of the projected component of F along line AC. Yant
Problem I. The beam has a loose fit built-in support at B which allows the end of the beam to rotate through the angle e, = 0.75° when the load is applied, as shown in the detail. E = 72 GPa and |= 120 x 10°mm*. Determine the following: a. Reaction at A (kN) | 200 kN -2 m 2 m b. Moment at B (kN m) c. Slope at A in radians В d. Displacement at the application of 200kN load Detail
The force-couple system shown acts on atrapezoidal plate. a. Determine thevalue of M, if the system shown is equivalent to a single force acting at point C. b. The system shown is equivalent to a force couple system consisting of R and M2= 3000 kip-in clockwise. If M, in this case is 120 kip-in counterclockwise, determine the point of action of the resultant force R along line CD. 50° 1YZ kips 10 in 1X in 10 in 20 kips 35 kips 8x kips 2Y in 5o 1YZ kips Parameters X = 7, Y = 3, Z = 7 1X in 17 in 23 in 87 kips 137 kips 2Y in 8x kips 1YZ kips 18 in
Q3. The 500 N force acting on the frame is to be resolved into two components acting along the axis of the AB and AC. If the component of force along AC is required to be 300 N, directed from A to C, determine the magnitude of force acting along AB and the angle 0 of the 500 N force. Fu 500 N
(2) The built-up beam shown is made from a 20-mm-thick plate and two angle sections having 10-mm-thick legs. If the beam is subjected to an internal moment ofM = 120 kN.m, determine the percentage of this internal moment resisted by the central plate. 150 mm 20 mm 150 mm 150 mm 10 mm 10 mm 300 mm
Q3. The 500 N force acting on the frame is to be resolved into two components acting along the axis of the AB and AC. If the component of force along AC is required to be 300 N, directed from A to C, determine the magnitude of force acting along AB and the angle 0 of the 500 N force. F 500 N
F2 F3 Let F = 12N, F2 = 50N and 8 = 139°. %3D %3D a) Find the magnitude F3 so that the resultant FR of the three forces is parallel to F1.
Determine the moment of the vertical reaction at point A (A,) rotating about the location (XR) of the equivalent resultant force of the forces acting on the beam shown in Figure 3.1f, i.e. A, X XR. Given /= 1.8, P1 = 30, P2 = 20 and w = 10. (Note: Negative "." for clockwise moment.) [Hint: Find the equivalent resultant force and its location (xR) with respect to point A. Apply correct equation of equilibrium to solve Ay. ] P, kN W kN/m P, kN 21 m 21 m Figure 3.1f
Determine the magnitude of the projectedcomponent of the force F = 300 N acting along line OA.
Examples Determine the moment of each of the three forces about point A. F2 = 300 N F = 250 N 30 %3D -2 m 3 m- 4 m orce where MA = Fd, we have = -250(1.732) = - F1 cos (30) * 2 = -433 N• m = 433 N m (Clockwise) F3= 500 N
8. In figure shown assuming clockwise moments as positive, compute the moment of force F = 90kN at points A and D. If each square is 1m on a side. A F=90KN C 1 в A. MA = - 432KN-m; MD = 216kN-m B. MA = - 162kN-m; MD = 180KN-m %3D C. MA = - 270KN-m; MD = 162kN-m D. MA = - 126KN-m; MD = 54kN-m P75KN