Q₁: Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k-2.3 W/m °C, and surface area A= 20 m². The left side of the wall at x= 0 is subjected of T1 = 80°C. while the right side losses heated by convection to the surrounding air at T-15 °C with a heat transfer coefficient of h=24 W/m² °C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat transfer through the wall Ans: (c) 6030 W

Q₁: Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k-2.3 W/m °C, and surface area A= 20 m². The left side of the wall at x= 0 is subjected of T1 = 80°C. while the right side losses heated by convection to the surrounding air at T-15 °C with a heat transfer coefficient of h=24 W/m² °C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat transfer through the wall Ans: (c) 6030 W

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.25P: Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner...

See similar textbooks

Similar questions

1.67 In beauty salons and in homes, a ubiquitous device is the hairdryer. The front end of a typical hairdryer is idealized as a thin-walled cylindrical duct with a 6-cm diameter with a fan at the inlet that blows air over an electric heating coil as schematically shown in the figure. The design of this appliance requires two power settings, with which the air blown over the electric heating coil is heated from the ambient temperature of to an outlet temperature of and with exit air velocities of 1.0 m/s and 1.5 m/s. Estimate the electric power required for the heating coil to meet these conditions, assuming that heat loss from the outside of the dryer duct is neglected.
Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinder
Q1: Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k=2.3 W/m °C, and surface area A= 20 m2. The left side of the wall at x= 0 is subjected of T1 = 80°C. while the right side losses heated by convection to the surrounding air at T-15 °C with a heat transfer coefficient of h=24 W/m2 C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat transfer through the wall Ans : (c) 6030 W
Q: A large plane wall of thickness (L= 0.3 m), thermal conductivity (k = 40 W/m-°C), and surface area 0.4 m2. The left side of the wall is maintained at a constant temperature of 70°C while the right side loses heat to the surrounding air with heat flux q' expressed by: 1200k q = k+20L A- Find a relation to determine the variation of temperature in the wall. B- Determine the rate of heat transfer through the wall. C- Determine the temperature at the right side of the wall. wall T1= 70 °C L= 0.3m
Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k=2.3 W/m °C, and surface area A= 20 m2. The left side of the wall at x= 0 is subjected of T1 = 80°C. while the right side losses heated by convection to the surrounding air at T∞=15 oC with a heat transfer coefficient of h=24 W/m2 oC . Assuming constant thermal conductivity and no heatgeneration in the wall, (a) express the differential equation and the boundary conditions forsteady one-dimensional heat conduction through the wall, (b) obtain a relation for thevariation of temperature in the wall by solving the differential equation, and (c) evaluate therate of heat transfer through the wall
Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k=2.3 W/m °C,and surface area A= 20 m2. The left side of the wall at x= 0 is subjected of T1 = 80 C. while the right side losses heated by convection to the surrounding air at Too=15 C with a heat transfer coefficient of h=24 W/m2 .C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat transfer through the wall
A rectangular wall of length "L" m and height "H" m is made from a thick bricklayer. The rectangular wall has a surface area as 11 m2 & Thermal conductivity as 0.53 W/mK. The wall is subjected to heat transfer due to the outside temperature 43 °C and inside temperature 24 °C. If the energy loss is 11219 kJ in 484 minutes. (HINT: 1 minute = 60 %3D seconds) Determine the following -- i) Heat transfer rate, ii) Thickness of the wall.
A large plane wall has a thickness of 0.4 m, thermal conductivity k= 2.3 W/m. °C, and surface area 30 m?. The left side of the wall is maintained at a constant temperature of 90°C while the right side loses heat by convection to the surrounding air at 25°C with a heat transfer coefficient of 24 W/m². °C. Assuming constant thermal conductivity and no heat generation in the wall, (i) Express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall (ii) Obtain a relation for the variation of temperature in the wall (iii) Evaluate the rate of heat transfer through the wall
The temperature distribution across a wall 0.3 m thick at a certain instant of time is T(x) = a+ b+cx?, where T is in degrees Celsius and x is in meters, a = 200°C,b = -200°, and c = conductivity of 1 W /m · K. 30°C/m² . The wall has a thermal (a) On a unit surface area basis, determine the rate of heat transfer into and out of the wall and the rate of change of energy stored by the wall. (b) If the cold surface is exposed to a fluid at 100°C, what is the convection coefficient? k=1W/m•k T(x) =200-200x + 30x² 200°C- ĖST 142.7°C q"out | Fluid Too = 100°C,h 9"in |L-0.3m
Q2: A hot surface at 150°C is to be cooled by attaching 4- cm-long, 0.3-cm-diameter aluminum pin fins (k = 200 W/m • °C) to it, with a center- %3D to-center distance of 1 cm. The temperature of the surrounding medium is 25°C, and the heat transfer coefficient on the surfaces is 40 W/m2.°C. Determine the rate of heat transfer from the surface for a 2m * 2m section of the plate. Also determine the overall effectiveness of *.the fins
Q2. Steam pumped through a long- insulated pipe at a temperature of T= 500 K and provides a convection coefficient of h, = 100 W/m?K at the inner surface of the pipe. The inner and outer radius of the pipe and insulation material are r1 = 10, r2 = 12 and r3 = 17 cm, respectively. The thermal conductivity of the pipe is 100 W/mK. The insulation material is glass fiber and its outer surface is exposed to ambient air at 300 K. If the ambient air provides a convection coefficient of ho = 20 Internal flow Ambient air W/m?K, determine the followings: a. What are the thermal resistance coefficients for convections and conductions b. What is the heat transfer rate per unit length of the pipe c. If the pipe is 30 m long, what will be total heat transfer rate from the pipe. t00 noints)
Q1/ Consider a large plane wall of thickness L=0.03 m. The wall surface at x =0 is insulated, while the surface at x =L is maintained at a temperature of 30°C. The thermal conductivity of the wall is k=25 W/m °C, and heat is generated in the wall at a rate of g = 9oe0.5x/L W/m³ Where g, = 8 x 10 W /m². Assuming steady one-dimensional heat transfer, (a) express the differential equation and the boundary conditions for heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) determine the temperature of the insulated surface of the wall.