Answered: Pull-out torque of a SCIM occurs at…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter39: Synchronous Motor Operation

Section: Chapter Questions

Problem 14SQ: Induction motors and welding transformers require magnetizing current, which causes a. lagging power...

See similar textbooks

Question

100%

Pull-out torque of a SCIM occurs at that value of slip where rotor power factor equals

a) unity

b) 0.707

c) 0.866

d) 0.5

Expert Solution

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A 2 pole wave wound dc generator has 44 slots, each slot having 20 conductors. The flux/pole is 0.018 weber. At what speed the armature be rotated to get an induced emf of 220 V. What will be the induced emf developed if the armature winding is lap connected and runs at the same speed. Speed Generated Emf when lap connected
The frequency of voltage generated in SG depends on: Select one:a. Number of polesb. number of poles and speed rotationc. Field currentd. Rotor speede.Number of poles, speed rotation and type of winding
A lap-winding DC machine has 24 coils, 18 turns per coil, and 4 poles. The average flux density per pole is 1T. The effective length is 40 cm and the armature radius is 10 cm. The armature velocity is 140.2 rad/sec and the armature current is 24 A. The average flux per pole in Wb is: 6.283 0.06283 O 0.6283 0.006283
A DC machine has total armature ampere conductors of 4500 and total flux in the machine is 0.14 wb. The torque developed in the machine is (in N-m/rad)
At certain instant, the angle (Өe) of the rotor flux vector is 60° .The output signals ids and iqs from the flux and torque controllers are 20A and 40A, respectively. Find the required (reference) values of individual phase currents in the stator
18. A 4-pole lap-wound armature has 144 slots with two coil sides per slot, each coil having two turns. If the flux per pole is 20-mWb and the armature rotates at 720-rpm. What is the induced voltage? B. 138.24 V C. 332 V D. none of these A. 120 V pruttha
A magnetic ring has reluctance of 1.675 × 10⁰ AT weber. The flux to be produced by the coil is 800 x 10 webers, then the AT required for the m.m.f. will be
6. Home Works: a) The figure below shows the per-phase equivalent circuit of a two- pole three-phase induction motor operating at 50 Hz. The voltage (E1) across the magnetizing inductance is 210 V, and the slip (s) is 0.05. What is the developed torque produced by the motor ? 0.04 0 jo.22 Q j0.22 0 j6.28 NE E1 0.05 0
The armature of a two-pole generator is rotating at 3600 r/min. The armature has a simplex lap winding with a total of 1504 conductors. Determine the generated voltage when the flux per pole is 600,000 x 10-8 Wb. 5.5
6. Home Works: a) The figure below shows the per-phase equivalent circuit of a two- pole three-phase induction motor operating at 50 Hz. The voltage (E1) across the magnetizing inductance is 210 V, and the slip (s) is 0.05. What is the developed torque produced by the motor ? 0.04 N jo.22 Q j0.22 0 0.05 0 j6.28 NE E1 V
The terminal voltage of a 150 kW series generator is 600 V at rated load. The armature resistance is 0.06 ohms and the series field resistance is 0.04 ohms. Find generated emf.
A 4 pole dc generator runs at 750 rpm and generates an emf of 240 V. The armature is wave wound and has 792 conductors. If the total flux from each pole is 0.0145 Wb, If leakage coefficient is given as the ratio of the total flux/pole to the working flux per pole, find its value.

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS