Question 1(a) The force of the block for holding the gate (b) vertical is T. If gate (a), (b), and (c) ofnegligible weight and used to hold water in a channel width b, determine in terms of T theforce for block gate (a) and (c)HingeBlockla)(b)(c)

Name: Question 1(a) The force of the block for holding the gate (b) vertica
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Question 1(a) The force of the block for holding the gate (b) vertical is T. If gate (a), (b), and (c) ofnegligible weight and used to hold water in a channel width b, determine in terms of T theforce for block gate (a) and (c)HingeBlockla)(b)(c)

Given: Force holding the gate for figure B is T TO determine: The force require to hold gate a and…

Answered: negligible weight and used to hold…

Engineering

Mechanical Engineering

negligible weight and used to hold water in a channel width b, determine in terms of T the force for block gate (a) and (c)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.119P: Determine the force F required to pull up the 3.54m stopper from the drain of a sink if the depth of...

See similar textbooks

Similar questions

Determine the force F required to pull up the 3.54m stopper from the drain of a sink if the depth of water is 10 in. Use =0.036lb/in.3 for water and neglect the weight of the chain.
4. A heavy car plunges into a lake during an accident and lands at the bottom of the lake on its wheels. The door is 1.2 m high and 1 m wide, and the top edge of the door is 8.8 m below the free surface of the water. Determine the hydrostatic force on the door and its location from the free surface. 8.8m Z Lake
A gate AB 4 ft long and 2 ft wide is held in position shown due to the spring whose constant is 96.0 Ibf/in. The spring is located compressed 1.5 ft in such a way as to keep the gate in equilibrium. Assume that on the gate (which moves through a circular sector BD as shown in Fig. figure), the force due to the spring is always horizontal. Determine the height d of the water.
... hinge 1.2m water 2.4m 1.8m A rectangular gate AB shown is hinged at "A" and rests on a smooth floor at "B". The gate is 1.5m wide. Determine the normal force "N" at point B neglecting the weight of the gate. A) 103.01 KN В No answer among the choices 84.84 KN 95.67 KN 72.19 KN
A person wearing long snowshoes can walk across a blanket of freshly fallen snow without sinking far into the snow because (p.s. Google snowshoe if you don't know how one looks like) snowshoes cover a larger area than a foot and so the pressure is reduced. the snowshoes reduce the force of the person on the snow. the large area of the snowshoe concentrates the force of the person to a point smaller than the foot. snowshoes push less dense snow out of the way so the person stands on more solid ice below
Ocean Marsh d = 9 ft 5.79 A freshwater marsh is drained to the ocean through an automatic tide gate that is 4 ft wide and 3 ft high. The gate is ħeld by hinges located along its top edge at A and bears on a sill at B. At a given time, the water levels in the marsh and in the ocean are h = 6 ft and d = 9 ft, respectively. Determine the force exerted by the sill on the gate at B and the hinge reaction at A. (Specific weight of salt water = 64 lb/ft³.) h =6 ft 3 ft B Fig. P5.79
The 20-ft-long gate of Fig. 1s a quarter circle 6 ft and is hinged at H. Determine the horizontal force, P, required to hold the gate in place. Neglect friction at the hinge and the weight of the gate. Water Gate H Hinge
4.0 m السرو 4.0 m The raft is made of solid square Pinewood (density= 550 kg/m'). Determine whether the raft floats in water (density = 1000 kg/m) and if so, how much of the raft is beneath the water surface. Weight of raft 0.30 m Since the density of the raft (pinewood) is less than that of water, the raft foats. Q: A force of 250 N is applied to a hydraulic piston that is 0.01 m in diameter. If the piston which supports the load has a diameter of 0.10 m, approximately how much mas can be lifted? 250 N 0.01 m 0.10 m
The spring clamp of Fig. block Fagainst the floor. The force in the spring is F = k(e – lo), where e is the present length of the spring, lo = 3 in. is the unstretched length of the spring, and k = 240 lb/ft is the spring constant. Determine all forces acting on mem- ber ÁBC of the spring clamp and the force exerted by the spring clamp on the block E. is used to hold the 8 in. D E 8 in. 6 in -6 in.- 6 in.
Figure 3 shows the plan view (top view) of a pair of gates which are hinged at the water channel walls. The channel has a depth of 9 m and a width of 40 m. When the gates close, the gate edges are forced together at the center of the channel by water pressure. While neglecting the weight of the gates determine: (a) The force exerted by the water on one gate (b) The magnitude and direction of the force components exerted by the gate in part (a) on the hinge. -Hinge Water 20°
keep the gate from opening when The circular gate ABC has a Im radius and is hinged at B. Compute the force P just sufficient to Question-2 (h 8 m). Neglect atmospheric pressure. ( = 9790 kN) Water P. Im Im
A homogeneous, 5-ft-wide, 8-ft-long rectangular gate weighing 900 Ib is held in place by a horizontal flexible cable as shown in the figure. Water acts against the gate, which is hinged at point A. Friction in the hinge is negligible. Determine the tension in the cable in Ib. Cable 60° Water Gate 6 ft 8 ft Hinge Round your answer to 2 decimal places. Add your answer