Make a detailed drawing of a Woodruff key connection between a shaft and the hub of a gear. The shaft has a diameter of 1.500 in. Use a no. 1210 Woodruff key. Dimension the key seat in the shaft and the hub and compute the torque that could be transmitted by the key based on shear and bearing if the key is made from C1118 cold-drawn steel with a design factor of N = 3.

Make a detailed drawing of a Woodruff key connection between a shaft and the hub of a gear. The shaft has a diameter of 1.500 in. Use a no. 1210 Woodruff key. Dimension the key seat in the shaft and the hub and compute the torque that could be transmitted by the key based on shear and bearing if the key is made from C1118 cold-drawn steel with a design factor of N = 3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pair of iron cast gears connecting two shafts at the Angle of the elbow. The diameter of the pinion pitch and the gear is 80 mm and 100 mm. The shape of the gear gear was 14 restriction form. The static voltage allowed for both gear is 55 mpa. If the door transports to 2.95 kw power at the turn of 1200 RPM, identify the module and the number of teeth on each gear from the Angle of power and check the design from the Angle of the tear. Take the surface durability limit is 630 mpa and the modulus elasticity to iron cast is 84 kn /mm2.
A steel shaft of 2.5 inch diameter rotates at 500 rev/min and transmits 120 hp through a gear. Select an appropriate square key for the gear, while the key material having yield strength of 60 kpsi. Assume a factor of safety of 2.0.. Draw sketch and show all calculations.
(4) An electric motor purchased by your employer surprisingly arrived without a keyway in the shaft. The motor has power rating of 7.5kW & 1,800rpm & has a shaft of Ø17mm. It will be used to drive a centrifugal pump using cast iron sheave. Design the square key to be used in the assembly based on maximum bearing & shearing stresses of 580MPa & 370MPa, respectively, and factor of safety of 5.
An SAE 1050 Cold drawn steel is to be used for a square or rectangular key. The shaft is made of SAE 4340 OQT400 and the diameter is 2.5 inches. The torque transmitted by shaft is 15,000 lb-in. Design factor, N=2. The hub is made of SAE4340 OQT400and the length of hub is designed to be 3 inches. Which one of the following square keys can be used for this design? Note: How do I determine answer if the diameter is between two values? (a) 0.375 in x 0.375 in (b) 0.500 in x 0.500 in (c) 0.625 in x 0.625 in (d) 0.750 in x 0.750 in
A power transmission shaft is to carry a steady 30 horsepower whilerotating at 1000 rpm. Specify a suitable diameter for the solid circular shaft if it is tobe made from AISI 1020 cold-drawn steel. Use Appendix A-2 for preferred size.
A 76.2 mm diameter shafting of SAE 1040 grade, cold, rolled, having yield point of 50 ksi and with a ¾ x ¾ x 5 inches key. Compute the minimum yield point in the key in order to transmitt he torque of the shaft. The factor of safety to use is 2 and Sys = 0.5 Sy. (Ans: 47.12 ksi)
A shaft where a hub is mounted has 2 in diameter, transmitting 20 hp power at 750 rpm. Design a square key made of steel for factor of safety (n) =3. Use preferred sizes.
The minimum required length of a key for a gear carrying 20000 lb.in of torque if it is mounted on a 3.5 in diameter shaft is most likely: Consider SAE 1018 as the key material. 1.29 3.5 1.53 1.45
A chain sprocket system is designed to drive a shaft. Assume the following conditions: Use SAE1018 steel for the key (which is the weakest material in comparison to other components) The chain sprocket has a bore diameter of 2.5" and the hub length of 3.125". The sprocket delivers 110 horsepower to a shaft with the rotation of 1700 rpm. Safety factor of 3 Determine 1). The dimensions of the square key: Width: in Minimum length (so the key will not fail): in 2). The minimum contact length on the hub (so the hub will not fail): in
The standard cross-section for a flat key, which is fitted on a 50 mm diameter shaft, is 16 x 10 mm. The key is transmitting 475 N-m torque from the shaft to the hub. The key is made of commercial steel (oy = 230 N/mm²).if the factor of safety is 3. Determine the length of the key.
A portion of the shaft where a gear is to be mounted has a diameter of 1.5in. The gear transmits 3000 lb.in of torque. The shaft is made of SAE 1040 OQT400 steel, the gear is made of SAE 8650 OQT1300 steel, and the key is made of SAE 1045. The minimum required length for this key is most likely: 0.5in 2.5in 3.0in 1.0in 1.5in
A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.