Given : Mass of Gears A and B = 2.4 kgsMass of Gear C = 12 kgsGears A and B's radius of gyration = 60mmGear C's radius of gyration = 150mmCouple M applied to gear B = constant 10NM%3DRequired : Number of revolutions of gear C in order for it to increase from 100 rpm to 450 rpmand Tangential force acting on gear A BS0 mmS0 mm200 mm .CM

Answered: Image /qna-images/answer/98869f86-d268-4157-b677-9fe83cf1465c.jpg

Given : Mass of Gears A and B = 2.4 kgs Mass of Gear C = 12 kgs Gears A and B's radius of gyration = 60mm Gear C's radius of gyration = 150mm Couple M applied to gear B = constant 10NM Required : Number of revolutions of gear C in order for it to increase from 100 rpm to 450 rpm and Tangential force acting on gear A

Given : Mass of Gears A and B = 2.4 kgs Mass of Gear C = 12 kgs Gears A and B's radius of gyration = 60mm Gear C's radius of gyration = 150mm Couple M applied to gear B = constant 10NM Required : Number of revolutions of gear C in order for it to increase from 100 rpm to 450 rpm and Tangential force acting on gear A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

consider a planetary train in the figure the number of teeth on gear sol (2) is Z2=30, the number of teeth on gear planeta (3) is Z3 = 20 and the number of gear anel (4) Z4 = 70 the speed of gear sol, w2 = 300 rpm and of anel w4 = 200 rpm find the speeds of gear sol and braço carregador b Anel (4) Planeta (3) ARRANT Sol (2)
P5/ The wheel of metor Cycle and the engine parts have antoment of inertia 2-5 kg.m? and o 15 Kg.m² respectively The axis of rotation of the engine erank Shaft is parallel to that of the road wheels-If the gear ratio is 5:1 and the diameter o f the read whels is o.65 m, find the magnitude and direction of the gyroscopic Couple when the motor Cycle rounds a eurve of Bom radius at l6 m/s.
Draw free-body diagrams of the two gears, assuming an input couple M on theOUT X shaft of the larger gear in the direction shown. Include forces at bearings A, B, D and E. M isthe reaction couple at the output shaft - i.e. the resistance to turning of the object being driven.The gears have 48 and 24 teeth respectively. If the input gear (large gear) turns at 100 rpm(= revolutions per minute), the output speed (small gear) is _______rpm.Wil OUT X IN Xl M be larger or smaller than M ?
In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc = 392 lb-ft is removed from the shaft at gear C, and the remaining torque is removed at gear D. Assume that DA-4-in.-diameter, Dg=12-in.-diameter, L₁=56 in., and L₂-30 in. Segments (1) and (2) are solid 1.5-in.-diameter steel [G = 12200 ksi] shafts, and the bearings shown allow free rotation of the shaft. Determine: (a) the maximum shear stresses T₁, T₂ in segments (1) and (2) of the shaft. (b) the rotation angle D/B of gear D relative to gear B. Answers: (a) T₁ (b) D/B = = i ᎠᏴ ; A DA i B L₁ Tc amala ksi, T₂ = L2 i Tp D ksi.
Spur gear train is used to transmit the power of 2kW from input gear A rotating at 120 rpm to output gear D through a compound gear BC. The number of teeth on the gear A, B, C and D are 16, 32, 12 and 18 respectively. Given: Module = 4mm, pressure angle=20° The tangential force acting on the gear B is N A D В
a) Fig. 3 shows a gear train that is attached to a rack labelled A. The rack is capable of moving up and down. Determine linear velocity and direction of the rack if the input gear 2 rotates at 1200 rpm counterclockwise. Assume the raduis of gear 8 is 12cm and all the number of teeth of the gear given in the diagram. @₂= 1200 rev/min 187 3 15T 44T 5 33T 16T 36T 8 487 A
The crank-rocker mechanism shown has lengths n = 9 in, r2 = 2 in, r3 = 7 in, andr4= 10 in. Find the angular displacement Aa that crank OA makes to move the rocker OpB from the extreme right to the extreme left position. Crank OAA rotates counterclockwise as shown. Write your answer in degrees but do not write the units. B A 0B Answer. DELL
The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to accelerate a flywheel at 0.1 rad/s2. The input gear has 11 teeth, and the output gear has 99 teeth. What is the flywheel's inertia? T=3N O O Input gear 11 teeth. Output gear 99 teeth 270 kgm² 57 kgm2 2.7 kgm2 Don't Know 27 kgm2 Flywheel 0.1 rad/s²
Qs1 The wheel of metor Cy cle and the engine parts have anoment of inertia 2-5 kg.m? and o 15 kg.m? respectively The axis of rotation of the engine erank Shaft is parallel to that of the road whels-If the gear ratio is 5:1 and the diameter of the read wheels is o.65 m, find the magnitude and direction of the gyroscopic Couple when the motor Cycle rounds a eurve of 3om radius at 16 m/s.
In the image on the right, there is a red gear G1 on the left with a radius of r1 = 2.81cm. Gear G1 is locked to the green gear G2 with a radius of r2 = 0.734cm. Gear G2 then shares the same axle as the blue circular saw G3, which has a radius of r3 known to make a full rotation every T = 0.836s. Using at least 6 significant digits in your calculations, compute the following: V3! 12.8cm. Gear G1 is W1 a) The angular speed wi of gear G1. Remember that angular speed is measured in radians per T3 r2 unit time. G2 b) The rim speed vi of gear G1. Since gears G1 and G2 are locked together, the rim speed of G2 is also v1. G1 G3 c) The angular speed w2 of gear G2. Since gear G2 and saw G3 share the same axle, the angular speed of G3 is also w2. d) The rim speed v3 of saw G3.
Three spur gear are arranged shown in the figure. Pinion A rotates for about 500 rpm. The three gears have a diametral pitch of 5. Number of teath and angle is shown in the figure. Determine the torque that each shaft is required to transmit and the resultant force on the shaft carrying the gear B. Draw the FBD of the figure.
Assignent no 1 Qt+ A Compound gear 6 Jears. No of teeth; train Consists of A B D 60 40 35 २४ 50 30 shaft on another shaft. The Gears B ş C are on one while are gears Gear A drives c drives gear D B, gear gear S gear E drives gear F. Gear A transmits 1.5 Kw at 15orpm Find speed of Gear F ? Q2+ State advatages of Cycloidal In volute profile as a gear tooth pnfile.