Find the torque that a 2-surface dry disk clutch can transmit if the outside and inside lining diameters are 120 mm and 70 mm, respectively, and the applied force is 10 kN. Assume uniform wear and μ = 0.4.

Find the torque that a 2-surface dry disk clutch can transmit if the outside and inside lining diameters are 120 mm and 70 mm, respectively, and the applied force is 10 kN. Assume uniform wear and μ = 0.4.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter22: Welding Joint Design And Welding Symbols

Section: Chapter Questions

Problem 4R: Sketch a V-grooved butt joint, and label all of the joint's dimensions.

See similar textbooks

Related questions

Q: The hard copper containing solder (L-Cu) connection in Figure 4 is designed to be forced with a…

A: GivenF=18000Nb=30mm

Q: A static load of 30 kN is applied at the cantilevered beam as shown in the Figure 3.1 The cantilever…

Q: Outline the principle of Ultra Sonic testing for checking deeply imbedded defects in a welded joint.

A: Ultra sonic testing is one the non destructive technique used for testing the defects inside a solid…

Q: A cylindrical air-compressor tank with an inside diameter of 50 mm is to be designed to withstand…

A: Logitudinal stress is stress which produces due to pressure or forces which does not exceed the…

Q: 11.6 Two 15-mm steel plates with S, = 400 MPa are butt-welded using E70 series weld- ing rods and…

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

A: we have to calculate the maximum force so that failure does not happen.

Q: II. Calculation Questions 1. The fillet welds are used in the joint. The design value of the weld…

A: Failure of welded joint can be checked for both the forces separately so that we can ensure it is…

Q: A welded joint on a mining machine is subject to cyclical stresses with a nominal stress range of 50…

A: The correct answer from the above problem would be 1.02x107

Q: plat system IS sugge the thickness of plate. 1 is 12 mm and plate. 2 is 10 mm. The yield stres…

Q: 6) In the given Fig. 2, the butt-welded joint is subjected to uniaxial tensile load of 10 kN, with…

A: Given data: Load = 10 KN h= 5 mm L= 100 mm Need to determine the maximum stress.

Q: In Figure 1, m=800 kg load is carried by the rope-pulley system. The reel is fixed to the fork with…

A: Given that, Mass of the load, m=800 kg,Factor of safety, FOS=6,Welded bar is 1030 Anealed steel…

Q: Why is it better to secure the rigging higher upon the load rather than lower? Explain

A: The Rigging is used in material handling system. For moving the material from one location to…

Q: Assuming a minimum design factor = 2.00, Design the bolted cover of pressure vessel; determine the…

Q: PROBLEM 02: Design a SMAW fillet welds to resist the load applied on the connection shown. Use E70…

Q: Q2/ The bracket shown in Figure (2) support a repeated load of 4000 N. The fillet weld extends for…

A: Given, Load ,W=4000lbeccentric distance, e=3inNo. of welds, n=2Shear stress due to direct…

Q: 5. A triple riveted lap joint with zig-zag riveting is to be designed to connect two plates of 6 mm…

A: solution:-Given datat=6 mmAssume σt=120mPaT=100 mPaσc=150 mPadiameter of rivetd=6t=6*6d=14.69 mmd=15…

Q: D)Two steel plates, 100 mm wide and 12.5 mm thick, are joined together by means of double transverse…

Q: Compute for the total length of weld required with the given tension load, T. Tension member is…

Q: Question 01: Draw and label any screw thread and a fastener separately. Also, discuss the types of…

A: As per the Question Demand of Draw and label any Screw thread and fastener . SO, screw thread-Square…

Q: Нome work 1. A plate( 100 mm) wide and (10 mm) thick is to be welded with another plate by means of…

A: Image_1

Q: Using SMAW process, E70 electrodes and an A572 steel. Determine the length of the side fillet welds…

Q: Design the length of weld (L) in the connection below to develop the full tensile capacity of the…

A: Electrode = E70, Welse side = 1/4" ASTM 36 allowable tensile stress = 22000 PSI Lenght of the weld…

Q: Fig. 8.76 8.6 A welded joint, as shown in Fig. 8.77, is subjected to an eccentric load of 2500 N.…

Q: T3.2.1The bracket shown below is to support a total load (equally divided between the two sides) of…

A: Given data as per the question safety factor = 3 Calculations T=F2(55+x)=30×103(55+22.5)=2.325×106…

Q: 20 m A riveted lap joint is shown in the figure. The rivets used are A502, Grade 2, hot-driven with…

A: The above given system of rivets can be subjected to failure by 5 different criterions which are as…

Q: 1, the plates are joined by a double riveted lap joint and pitcli the riveted ioint and (ii)…

Q: 3. A single riveted double cover butt joint is made in( 10 mm) thick plates with (20 mm) diameter…

A: Given data:

Q: An overlapped fillet welded lap joint is subjected to cyclical stresses with a nominal stress range…

A: HERE GIVEN WE HAVE NOMINAL STRESS =100MPamaximum plate thickness =20 mmcapacity factor = 0.90

Q: Design a cotter joint to support a axial load of122kN kN . Carbon steel material selected which…

Q: T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for full 100 mm…

Q: 11. According to the Goodman criteria, how should the fatigue factor of safety change for a tension…

A: suppose σa= σmax-σmin2=x ; σm= σmax+ σmin2=y ; σe and σu are constant Now we are increasing…

Q: Two plates, 20 mm thick, are welded together by means of transverse-fillet welds. The ultimate…

A: Given Data Ultimate tensile strength is: sut=415 MPa Endurance limit is Se'=0.5×sut=0.5×415=207.5…

Q: a) list two advantages and two disadvantages of welded joints b

A: Dear student, there are multiple questions. We are suppose to solve only one question. Please post…

Q: QI: The steel strap with thickness of 12 mm is to be welded to a rigid frame to carry a static load…

A: By distortion energy theory,

Q: Revie Part A The shaft in (Eouce.1) is used to tranamit 30 hp while turming at 500 rpm. Determine…

Q: for the lap joint shown below, calculate the safe axial tensile fo 126 102 A 220M

Q: Assuming that the quired weld size for the weld shown below using E60 welding rod (S, = 345 MPa) nd…

Q: 3.) The diagram below shows a 5.5m long double angle brace which is connected by 6mm welding…

A: given data

Q: A steel cylindrical air receiver with 5 feet diameter and pressure load of 180 psi, design stress of…

A: Given Tensile stress = 65,000 psi Design stress = 9500 psi Diameter, D = 5 ft…

Q: A lever arm is soldered to the drive shaft of a machine with a=30° angle. Drive shaft is rotated…

A: Given data: The angle of the lever arm with drive shaft is, α=30°. The drive shaft rotated with…

Q: What is the safety factor for this weld? F=671 Ibf, b=1 in; d=2.2 in; h=1/4 in. The weld metal is…

Q: Q2/ The bracket shown in Figure (2) support a repeated load of 4000 N. The fillet weld extends for…

A: This question is solved with the help of safe stress expression, As we know, the safe stress…

Q: An angle iron made of AISI 1040 CD steel is welded to metal as shown and loaded with a dynamic load…

A: Material AISI 1040 CD Propoerty: Sut = 590 MPa, Sy = 490 MPa Welding material property: Sut = 482…

Q: Two plates, 25 mm thick, are welded together by means of transverse-fillet welds. The ultimate…

A: Given Ultimate tensile strength Sut.=415 MPa Surface finish factor ka=0.5 Size factor kb=0.85…

Q: Two plates are a length (L) and thickness (t). were welded together. Assume these plates have…

A: When two plates of same length and thickness are joined together using welding, the lap joint would…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

Question 4
1. Two 10-mm-thick by 60-mm wide hot rolled SAE 1050 steel plates are to be butt-welded together with a CJP weld. Choose an appropriate electrode for tensile loading of the joint.

2. Find the torque that a 2-surface dry disk clutch can transmit if the outside and inside lining diameters are 120 mm and 70 mm, respectively, and the applied force is 10 kN. Assume uniform wear and μ = 0.4.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3.) The diagram below shows a 5.5m long double angle brace which is connected by 6mm welding connection. The length of weld shown in the picture is 300 mm on the top and 100 mm on the bottom. The 2-L127x 89x6.4 are 300W steel and long leg back-to-back. The braces are to be welded to a 12 mm 350W steel gusset plate. Determine the factored tensile capacity of the angles. Any intermediate connections that are required should also be specified. 740 kN -12 mm Gusset Plate
Te - Effective throat thickness well in mm = 6 sin45° Consider the following drawing in which plate 1 is welded onto plate 2 as shown for tensile and shear loading. The plates are fillet welded with a weld thickness of 6 mm as shown for a length of 150 mm. The plates have an ultimate strength of 275 MPa and the welding was done with F70 welding electrodes, which possesses an ultimate strength of 483 MPa. Consider a partial factor of safety of 1.7 for the welded joint and determine the design strength of the weld joint, both in tension (Tdw) and in shear (Vdw) due to the forces acting on it. a) Determine the design strength of the following weld in tension ( ) due to vertical forces. b) Determine the design strength of the weld in shear ( ) due to horizontal forces. Attached pic is shear equation for calculation Tension equation for calculation is: Tdw = FyLwte /Ymw
3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.
A cylindrical pressure vessel, mean radius 15 in, is filled with a gas of molecular weight causing an internal pressure of 3500 psi. The efficiency of welded connection in the vessel is 78%. Assuming the material of the vessel to have a yield strength of 12 x 10⁴ psi, calculate for this strength the thickness of the vessel assuming a factor of safety of 1.5. draw diagram
8. Design the length of weld (L) in the connection below to develop the full tensile capacity of the plate. Use E70 electrodes and 1/4" side fillet welds. The material is ASTM A36 Steel and the allowable axial tensile stress is 22,000 psi. (show all your work) "L" PL 1/2" PL 3/8" x 6" P
As shown in figure below, two plates are clamped by washer-faced 2 in-20 UNF SAE grade 5 bolts each with a standard 2 N steel plain washer. The top plate is steel and the bottom pplate is gray cast iron. If a total of 8 bolts where used to close 1 feet diameter pipe which applied at maximum pressure of 150 psi. Calculate the static and fatigue safety factor of this joint. Used Goodman theory for tha fatigue safety 1/2 factor. 3/4
Two plates, 25 mm thick, are welded together by means of trans verse-fillet welds. The ultimate tensile strength of a weld metal is 415 MPa. The surface finish factor of the weld surface is 0.5, and the size factor is 0.85. The reliability is 90%. Determine the length of the weld if the factor of safety is 2. The transverse force on the welds is 100 kN, which is completely reversed under fatigue loading. Take: A=10mm 25 Toe Р.
5. A triple riveted lap joint with zig-zag riveting is to be designed to connect two plates of 6 mm thickness. Determine the dia. of rivet, pitch of rivets and distance between the rows of rivet. Indicate how the joint will fail. Assume : o, = 120 MPa ; t = 100 MPa and o, = 150 MPa. %3D [Ans. d = 14 mm ; p = 78 mm; pb = 35.2 mm] %3D
200 mm 300 mm 42818 N B = 60° A lifting lug is to be mounted. The lug is shown on the drawing and the force is expected on the lug. The lug has a thickness of 30 mm. Calculate the minimum size of the weld for the given load case to ensure a minimum FOS of 3. Assume an AWS number E70xx electrode is used.
4. With tai yield strength of 393MP. JE the factor of safety is 4, calculate the allowable force E Strength of 210MPA. If the factor of safety is 4, calculate the key length. Note: fore circular shape welding A = 1.414 zhr J, = 2 nr F -045 930
Question 01: Draw and label any screw thread and a fastener separately. Also, discuss the types of stresses acting on screw threads and fasteners.
Determine the maximum, minimum and average pressure in a plate clutch when the axial force is 3.3kN. The inside radius of the contact surface is 81mm and the outside radius is 110 mm. Assume uniform wear.