Discuss how you add more voltages using the summing amplifier. - If the values of the input resistors changed, is it possible to obtain the sum of input voltages? - Explain how to obtain the average of the input voltages at the output. - Suggest possible application for the summing and difference amplifiers. Add any comments you think necessary based on th observations obtained from the experiment. +12 Ve Power ±12V Power 1K Supply 5V I/P1 IK Supply +12 -12V Variable + Power Supply 0-15V F12 IK I/P2 IK Figure 4 Table 2 I/P 1 I/P 2 O/P Volts Rf= 1k Volts Volts 5V 5V 1 5V 5V 5V 3. 5V Please write the solution in print

Discuss how you add more voltages using the summing amplifier. - If the values of the input resistors changed, is it possible to obtain the sum of input voltages? - Explain how to obtain the average of the input voltages at the output. - Suggest possible application for the summing and difference amplifiers. Add any comments you think necessary based on th observations obtained from the experiment. +12 Ve Power ±12V Power 1K Supply 5V I/P1 IK Supply +12 -12V Variable + Power Supply 0-15V F12 IK I/P2 IK Figure 4 Table 2 I/P 1 I/P 2 O/P Volts Rf= 1k Volts Volts 5V 5V 1 5V 5V 5V 3. 5V Please write the solution in print

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Questiona. In an experiment the voltage required for the device is 9V dc but unfortunately the transformer available is of 220-6 Vdc. Design a circuit which can power the device (use only methods that we have studied excluding Zener diode)b. Explain the behavior of the following circuits if the input signal is triangular wave of peak voltage 5V and the biasing battery of 3V
Design a DC-DC converter of the circuit with the following specifications: Input voltage (12-40) V; output voltage 24 V; output current is varied from (2 to 4)A: C.C.M with output voltage ripple not more than 1%. Knowing that the switching frequency is 25 kHz. Also draw the current waveforms. And give the Design specifications of diode (PIV, and Vavg ,I peak) and (V Diod , I Diod) of Diode. Buck Boost Converter lin ip + T | Va R ic i.
Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz (operating values). a) 0.11A b) 22mA to 89mA c) 9A d) 0.11A to 9A
Among its products is the power transducer. The product is an electrical isolation transducer of single-phase active and reactive power measurement, complete isolation between input and output signals. It is designed to measure power, reactive power and power factor. The product is widely used in electricity, communications, railways, industrial control and other fields. The transducer weights 0.7-pound, 1-500-volt, 0.5-700 A, the size is 76mmx32mmx2inch. The response time of the transducer is 250 ms. (a) 1. What is the volume of the transducer in cubic m? 2. How many transducers can be packed in box of 1m X 0.5 m X Qm? 3. If the factory produces 500 transducer per hour, how many minutes are needed to produce 50 kg of the transducer? 4. If the production line needs maintenance every 100,000 transducer. Find to the nearest integer how many weeks are needed to be sent to maintenance if the production rate is 100 transducer/min which operates 8 hours/ day and 5 days / week.
A. For the circuit diagram shown below, determine and sketch the output voltage (Vout). 1_ohm GaAs 1 ohm 1_ohm Ge Si A 1_ohm. 6_Vpeak w. Vout)
Q10. Determine maximum and minimum value of Zener current if value of series resistance is 1 K, load resistance is 2KN and input varies from 10V to 30V. Zener voltage is 5 V. Q11. What is LED? Q12. Which materials are used in manufacturing of LEDS?
5) In the single-phase full wave bridge rectifier circuit with a load of pure resistance, the input supply voltage is given as 220V , 60hz, the load resistance value is 15 Q. Compute the following a)average and rms value of output voltage b) average and rms value of output current P P: O N
Q2: A full-wave bridge rectifier is connected with RC load at frequency 50 Hz. The value of shunt capacitor and the dc output voltage are 0.450 mF, 16.5 V, respectively. The dc output current is 250 mA. What is the peak value of output voltage?
Plot the graphs of the outputs of the circuits in scale according to the input signal.and provide information about varactor structure and usage areas
In a temperature measurement system ,the element A receives the temperature value and produces millivoltage as the output. This output is given to an element B. The element B increases the millivoltage value into voltage value. Then it is given to element C. The element C converts the analog voltage into Digital value .The element D displays the output. Identify the elements A, B, C and D used in the above mentioned temperature measurement system.
Explain briefly the difference between passive and active components.
The Figure 2 shows an electronic circuit designed for supplying power to a load (R1). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. D1 Iide 91 Vaut VLoad D2 D3 Vde VI sine R1 RL Regulate Reetifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k The transistor Q1 with B value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator | (Idc) Base current of transistor (IB) Collector…