Determine the balanced hauls and indicate the direction of haul for the mass diagram showR below. The LPH is 4,000 ft. Also, show on the profile what cut sections will be hauled to what fill sections, and indicate any borrow or waste sections. Calculate the average haul distance for each balanced haul. 75000 50000

Determine the balanced hauls and indicate the direction of haul for the mass diagram showR below. The LPH is 4,000 ft. Also, show on the profile what cut sections will be hauled to what fill sections, and indicate any borrow or waste sections. Calculate the average haul distance for each balanced haul. 75000 50000

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.7P: A driven closed-ended pile, circular in cross section, is shown in Figure P12.7. Calculate the...

See similar textbooks

Similar questions

Q.5/A 3.75 Cyd wheel loader used to load trucks from a stockpile of mixed aggregate. The haul- return distance is 300 ft. calculate the estimated productivity of loader in tons (conservative) based on 50 min/hr. Efficiency? The loader will move forward on the first gear in haul and on the third forward in return; the unit weight is 3400 Ib/Cyd, and the swell percent is 20%.
Load combinations for ASD are given in the NSCP 2015 or ASCE 7 as follows. Combination 1: D Combination 2: D+L Combination 3: D+(L, or S or R) Combination 4: D+0.75L+0.75(L, or S or R) Combination 5: D±(0.6W or 0.7E) Given: D = 107 kN, L = 46 kN, Lr = 19 kN, S = 20 kN, E = 50 Required: Which of the following is the controlling load combination for ASD? 127 kN O 107 kN O 153 kN 142 kN
A belt conveyor is required to deliver crushed limestone having a bulk density of 75 lb/cu ft at the rate of 200 tons/hr. The conveyor is to be 200 ft between center of pulleys with a rise of 25 ft. The largest lumps are 4 in. and constitute 15% of the total. The conveyor will discharge over the end. For a belt speed of 200 fpm, what is the minimum width of belt that can be used? Calculate the horsepower for the drive motor.
A 3-cy wheel loader will be used to load trucks from a quarry stockpile of processed aggregates having a maximum size of _ in. The haul distance will be negligible. The aggregate has a loose unit weight of 2,950 lb per cu yd. Estimate the loader production in tons based on a 50-min hour efficiency factor. Use an aggressive cycle time and fill factor.
Estimate the hourly production in LCY of a 3 CY articulated wheel loader excavating hard materials from a pit and moving it to a stockpile. The average haul distance is 350 ft and the grade is 10%. The bucket fill factor is 1 and the efficiency is 45 min/hr. Find hourly production in LCY/HR. Please help me with right solution... Urgenttttttttt... Thank you
A 32-cy wheel loader will be used to load trucks from a quarry stockpile of processed aggregates having a maximum size of in. The haul distance will be negligible. The aggregate has a loose unit weight of 2,900 lb/cy. Estimate the loader production in tons based on a 50-min-hour efficiency factor. Use an aggressive cycle time and fill factor.
Which of the following terms describe shear yielding failure in block shear. O FuAnt O FYAG O 0.6FyAgv O 0.6FyAnv
5. For a systerm shown, determine the maximum weight of the box that will cause the crates to move up. Use coefficient of friction for contact surface, 0.35. 7
A bottom dump hydraulic shovel with a 5 cubic yard heaped capacity bucket is excavating in hard clay. The depth of the excavation is 12 feet. The shovel has a maximum rated digging depth of 34 feet. The haul units can be positioned so that the swing angle is 60 degrees. The job efficiency is 50 minutes per hour. Find the expected production per hour.
Class Prep Problem • Will the following crane tip over if it is picking up 7 kips? • The weight of the right axle is 3 kips and the weight of the left axle is 8 kips. 10 LOAD 45 Prove with calculations
If the deformation (permissible precipitation in the piles is 0.005m / kip according to the standard, and when examining a concrete substrate, destructive inspection, the maximum load was 1000 kip, and when measuring the net precipitation after removing the loads completely, it was 2.2 inch, the amount of precipitation)
Why do you split the 7 KN load ?