A road with 5.6% upward grade and speed 100kmph. If coefficient of longitudinal friction 0.33 and driver reaction time was 1.8sec, find the stopping sight distance available.A BI=E B $$ P *US X₂x² =E E##I</>CX

Answered: Image /qna-images/answer/5d755c9e-9ba7-4d1e-8e9f-3603c3d6198c.jpg

Answered: d with 5.6% upward grade and speed…

Engineering

Civil Engineering

d with 5.6% upward grade and speed 100kmph. If coefficient of longitudina BI. US X₂ x² "흐음

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: time to fill the bucket of water is wrong i believe

Q: Find the equation of the orthogonal of the set of the x² + (y + c)² = C² curves:

A: Given the family of curves is x2+(y+c)2=c2,here c is the parameter.

Q: Problem 4: Using USCS Method and the charts provided, classify the following soil = 23%, Percent…

Q: Applying the (AMM) Area Moment Method Approach. Consider 150 mm x 200 mm section and E = 80 GPa.…

Q: 6-43. Draw the shear and me A -X- 200 N/m -3 m-

Q: For the following structures, calculate -Reactions -Deformation diagrams (individual and general) An…

Q: Example 1: Given the water demand in an area is 710 gal/min, the local allowable maximum flow…

A: Given data,water demand in an area is 710 gal/minallowable maximum flow velocity is specified to be…

Q: H.W 5.5 If the rods are made from a square section with the dimension as shown. Calculate the load…

Q: The 10 ft rectangular wooden column has the dimensions indicated. Determine the critical load if It…

A: Length of the column (L) = 10 ft x 12 = 120 inModulus of elasticity of material (Ew) = 1.6 x 103…

Q: 1. The steel beam with an I cross section is loaded as shown below. 8 kN 20 kN m -2m-1m 2m- 15 kN/m…

Q: 9K6 D hol a 10 Feet RE to Feet .. Besuce OBDEL UNVEX 00.0

A: Given thatRadius = 10 ft

Q: P8.13 WP Two uniformly distributed loads w = 3,600 lb/ft act on the simply supported beam shown in…

A: A two sided overhanged simply supported beam is loaded as follows

Q: 2 kN 1.5 m 1.5 m -3 m- -1.5 m- 4 kN F -3m- -3 m- 2 kN -1.5 m- D

Q: (2) Draw the influence lines for (a) the vertical reaction at B, and (b) the moment at E. Assume the…

A: The continuous beam with an internal hinge is shown in the above figure. We have to find out the…

Q: A rigid pavement is to be used to carry a wheel load of 49KN, the allowable tensile stress of the…

A: The wheel load on the rigid pavement = 49 kNThe allowable tensile stress of concrete = 1.4…

Q: Given: this planar water jet (60°F) is deflected by a fixed vane. 40 ft/s 30° Toive 60° 0.1 ft 0.2…

A: Given data,fig is given,Initial velocity =40 ft/secdeflected one vane is 600 and another 300FINDx…

Q: 4. Determine the service load capacity of 2C10X20 channels as a truss member attached to a 7/8 in…

A: Grade of steel= A572 grade 65. Hence, yield strength= fy = 65.3 ksiUltimate strength fu = 79.8 ksi…

Q: Problem 1: Explain the mechanism of bond stress transfer in straight and hooked bars in tension

A: This question is related to the Design concrete structures from Civil Engineering.Find out - Explain…

Q: Should the moment at ED be 256.95? and i am not seeing you calculate that moment at E

Q: 3.24 The four forces are in equilibrium. Deter- mine F, and 0, (a) graphically from the force…

Q: supported as shown, determine: a) The normal stress in member DE if it has a cros ectional area of…

A: Area of membe DE =750mm2Stress in member BC is 30MPa

Q: The velocity profile of a liquid flowing through the pipe is approximated by the truncated conical…

Q: A car travels along the level curved road with a speed which is decreasing at the constant rate of…

Q: A. Determine the reactions of A and B. B. SOLVE THE TENSILE FORCE IN EACH MEMBER WITH DETAILED…

Q: A cylinndrical thin-walled vessel with an inside diameter of 24 inches is used to contain air at a…

A: We know that design of thin cylindrical vessel is controlled by circumferential stress(hoop…

Q: Example 4: Calculate the plastic section modulus about x axis. Y top __X__ y bottom O 400 200 10 20…

A: Unsymmetrical I section was given. We need to find plastic section modulus about x axis

Q: The state of stress at a point in a member is shown in A 0x' = 60° σ y B on the element. Assume ox…

Q: h * 中 A B t e F с * Compute vertical displacement at using Castigliano's theorem с

Q: 5- An abrupt rise of 0.8 m was designed to control a hydraulic jump generated after a 4 m wide…

A: Abrupt rise = 0.8 mWidth of sluice gate = 4 mOpening = 0.2 mFlow discharge = Flow depth = 1.2 mTo…

Q: Find the maximum live load can be applied to the beam shown in the figure (3-3). Use 4425 for…

A: b = 300 mmh = 500 mmfc = 33 MPafy = 414 MPamain bar = 4 - # 25 mmAssume clear cover = 30 mmTo…

Q: What do the moment diagrams look like for the real and reductent free body diagrams.

A: ALL DATA taken from given question RA=27.748 KNRc=17.252KNMA=38.244 KN

Q: Example 2 : Design a concrete mix to implement a concrete slab (exposed to sever conditions moisture…

A: f'c = 30 MPaS = 4 MPa FM = 2.4 Apparent density = 1500 kg/m3

Q: Recall that the Tatooine community has a population of 600663 residents and generate 0.7 kg of solid…

Q: can you help me please the solution is to find a deflection at B P = 250 kg, a = 0.7 m, E = 2x10^6…

A: E = 2 × 106 kg/cm2 Determine the deflection at point B.

Q: Problem 13.12 The 49-mm-diameter C86100 bronze rod is fixed supported at A and has a gap of 2 mm…

Q: The transport planners of City Y wish to introduce a major new public transport system to the city…

A: CRFTotal costAnnual passenger…

Q: Describe the potential implications of persuasive technology in the field of smart cities and urban…

A: Influencing Sustainable Behaviors:Environmental Awareness: Persuasive technology can enhance…

Q: 4.1 A line load of q = 60kN/m with a = 0 is placed on a ground surface as shown in Figure P4.1.…

Q: Design a column base plate for a W12 × 65 column supporting a service dead load of 850 kN and a…

A: W12 × 65 columnservice dead load = 850 kN service live load = 1380 kN concrete footing= 2.7 m x 2.7…

Q: For the beam and loading shown, determine the maximum normal stress due to bending on a transverse…

A: The given beam is shown below.

Q: A frame and loading are shown. B P 120 mm 120 mm D 120 mm 90 mm Determine the force acting on member…

A: Given:P = 320 NRequired:Force at C

Q: Determine the stress in each section of the bar shown in Fig. when subjected to an axial tensile…

A: P = 20 kN or 20,000 N E = 210 GPa or 210000 MPa

Q: As shown, a space truss is the frame for a building's awning. (Figure 2) Three ball-and-socket…

A: Given force vectorr =( 110i + 310j )NAt joint D the position vectors: DA = - 0.5i - 1.5j -…

Q: A saturated clay has a natural moisture content of 43%. Taking Gs = 2.70, calculate the void ratio,…

Q: 1. A hollow steel box beam has the rectangular cross section shown in the figure. Determine the…

Q: H.W: Find forces and elongations wires, steel in each wire. A=80mm² L=4m E=200 G Pa Estrelaxation.…

Q: 8.9 A continuous foundation on a deposit of sand layer is shown in Figure P8.9, along with the…

A: The elastic settlement of a foundation using the strain influence factor method of Schemertmann is…

Q: An urban catchment has an area of 0.85 km². The slope of the catchment is 0.006 and the maximum…

Q: Find the vertical deflection of the joint C of the pin joined three-member truss as shown in Fig. 2.…

Q: Determine the vertical displacement of joint A. Assume the members are pin connected at their end…

A: AE= constant,A=300 mm2 and E=200 Gpa

Concept explainers

Drainage of Pavements

Pavement Drainage holds ample significance, as it prevents the accumulation of water or any liquid on the surface of pavements and ensures proper drainage system. With proper design and gradual slopes provided, the water gets easily removed from the surface into the drains, which are essential during heavy rains and unusual weather conditions keeping it less prone to accidents and increasing the durability of the pavement structure.

Question

A road with 5.6% upward grade and speed 100kmph. If coefficient of longitudinal friction 0.33 and driver reaction time was 1.8sec, find the stopping sight distance available.
A BI
=
E B $$ P *
US X₂
x² =
E E
#
#I
</>
CX

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the stopping sight distance

VIEW

Step 2: Determine the stopping sight distance

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A car is traveling on a -4.20% grade for a design speed of 90 kph. Coefficient of friction between tires and pavement is 0.33. Driver's reaction time (including perception time) is 2.50 seconds. Determine the following: a.) acceleration of the vehicle in ft/s2 , b.) Stopping sight distance in meters. SHOW COMPLETE SOLUTION UPVOTE GUARANTEED asap.
7. From the Crest Vertical Curve Chart (attached) determine the Length of the Vertical Curve for a curve having a difference in grade of 5% and a design speed for this roadway of 60 mph. Vertical Curve
The stopping sight distance of a vehicle is 295 meters. Given that the acceleration of the vehicle is 3.45 m/s2 and travelling at a maximum grade of -3.5%, determine the following: a. Velocity of the vehicle in km/h b. Reaction distance in meters c. Braking distance in ft. Provide solution asap upvote guaranteed!
An auto, equipped with only front wheel brakes, has a wheelbase of 120 in. with its c.g. located 60 in. abead of the rear wheels and 36 in. above the pavement. If f= 0.80 at the tires, compute the minimum distance in which the auto can be brought to rest from a speed of 60 mph if the driver's reaction time before applying the brakes is 3/4sec. Come up with ans. S = 294 ft
What is the intersection sight distance (m) needed at a stop controlled intersection for a passenger car to turn left onto a 2-way, 4-lane road with a design speed of 80 km/h? Assume the vehicle turns into the closest lane. [round to the nearest meter] Response Feedback: ISD=0.278V t major g Remember, tg is increased by 0.5 seconds for the additional lane.
The rated speed of a highway curve of 60 m radius is 50 kph. If the coefficient of friction between the tires and the road is 0.25, (a) What is the minimum speed at which a car can round the curve without skidding? (b) What is the frictional force exerted on the wheels of the car when the speed observed is 35 kph? 1kph= 0.28 mps
H. W: A car hit a tree at an estimated speed of 35 mph on a 3% downgrade. A skid mark of 100 ft is observed on the pavement followed by 250 ft on the stabilized shoulder. Estimate the initial speed of the vehicle just before the pavement skid was begun. Use f = 0.45 for the pavement and f = 0.20 for the stabilized shoulder.
-) C Problem 1.3. Calculate the minimum non-passing sight distance on a highway at a descending gradient of 6%. Given tile following data : (i) Design speed = 80 kmph (ii) Reaction time of driver = 2.5 seconds. (iii) Coefficient of friction between tyre and road surface = 0.4 pogging sight
A ASHOK LEYLAND REQUIRED TO ACCELERATE AT A RATE OF 2 /SEC 2 IN THE FIRST GEAR FROM A SPEED OF 15 K.P.H THE GRADIENT IS + 3 PERCENTAGE AND THE ROAD HAS A BLACK TOPPED THE FRONTAL PROJECTION AREA OF THE CAR IS 3.0 M2.THE CAR TYRES HAVE A RADIUS OF 0.50 M. THE REAL AXLE GEAR RATIO IS 3.82 :1 AND THE FIRST GEAR RATIO IS 478 :1 .CALCULATE THE ENGINE HORSEPOWER NEEDED AND THE SPEED OF ENGINE. ASSUMING F= 0.04, TRANSMISSION EFFICIENCY OF 0.80, TYRE DEFORMATION FACTOR = 0.85, RO=0.60
The car is moving with a speed vo = 46 mi/hr up the 8-percent grade, and the driver applies the brakes at point A, causing all wheels to skid. The coefficient of kinetic friction for the rain-slicked road is lk = 0.61. Determine the stopping distance sĄB. Repeat your calculations for the case when the car is moving downhill from B to A. в 8 100 Answers: Uphill: SAB = ft Downhill: SBA i ft
35. Determine the minimum speed of a car at the point the brakes are immediately applied to avoid a collision based upon a yaw mark chord measuring 70.4 feet and a middle ordinate measuring 6 feet. The drag factor C² M of the road surface is 1.4 (Use-Mand S=√15fr ) A. 34.2 MPH B. 9.9 MPH C. 16.4 MPH D. 47.2 MPH
While traveling at a constant speed a driver saw a road block 112 m away. He applied the brakes and the car decelerated uniformly at 6.4 m/s2. It stopped 5 m from the block. The driver’s PRT is 2.2 seconds. Sketch and calculate the initial constant speed of the vehicle in kph if;a. The roadway is levelb. The roadway grade is +10%c. The roadway grade is -10%