Consider 1 g of sodium chloride that is successively divided into smaller cubes with various varying sizes as shown in table. Assuming a mass density of 2.178×10³ kg/m³ and surface energy of 2 × 10-5 J/cm², complete the table below and make your conclusion about how the total surface energy of 1 g of sodium chloride vary with particle size. Total surface area Side 0.1 cm 0.01 cm 0.001 cm 1 µm 1 nm Total Surface energy (J/g)

Consider 1 g of sodium chloride that is successively divided into smaller cubes with various varying sizes as shown in table. Assuming a mass density of 2.178×10³ kg/m³ and surface energy of 2 × 10-5 J/cm², complete the table below and make your conclusion about how the total surface energy of 1 g of sodium chloride vary with particle size. Total surface area Side 0.1 cm 0.01 cm 0.001 cm 1 µm 1 nm Total Surface energy (J/g)

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A cylinder containing 100.9 cubic centimeter of gas at a pressure of 376 kPa when its temperature is 534 K. Given that its temperature is unchanged when the pressure was increased by a factor of 5.9, Determine the new volume of the gas (In cubic centimeter). Note: Your answer must be in cubic centimeter, however, do not include the unit, just enter the magnitude that corresponds to the final volume in cubic centimeter. Round your answer to 2 decimal points Round your answer to 2 decimal points
A (1.1x10^1) liter bottle is filled with nitrogen (N2) at STP (Standard Temperature and Pressure is 1 atm and 273 K) and closed tight. If the temperature is raised to 100° C, what will be the new pressure in SI units to two significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 Answer
Consider an ideal gas at temperature T = 578 K and pressure p = 2 atm. Calculate the average volume per molecule in this gas in units of cubic nanometers (a nanometer is 10-9 m). Do not include units in your answer and state your answer as a number in normal form.
The power radiated by the Sun is 3.83 × 1026 W (The Watt is the SI unit of power, 1 W = 1 J s-1). Given that the power radiated by the Sun is the rate at which energy is radiated by the Sun per unit time, write down a formula relating the total energy radiated by the Sun, E, during a time interval T, and the radiated power, P. Use your formula and the information given above to calculate the total energy radiated by the Sun in exactly 4 hours. Give your answer to 3 significant figures and write it using scientific notation.
The pressure, volume, and temperature of a mole of an ideal gas are related by the equation PV = 8.31T, where P is measured in kilopascals, V in liters, and T in kelvins. Use differentials to find the approximate change in the pressure if the volume increases from 10 L to 10.6 L and the temperature decreases from 335 K to 330 K. (Note whether the change is positive or negative in your answer. I Round your answer to ti decimal places.
The pressure, P of an ideal gas, can be expressed as P = nRT/V where n is the number of moles, T is the temperature, V is the volume and R = 8.314JK^-1 mol^-1 is the ideal gas constant. a) Find the expression for deltaP in terms of deltan, deltaT and deltaV: deltaP = deltan + deltaT + deltaV b) Suppose that n = 1, V = 1m^3 and T = 300K initially. If n and V change to 9/5 and 7/10m^3 respectively, estimate the change in T(K) required to keep P constant.
The porous catalyst pellet shown in Figure 1 has an overall radius R and a thermal conductivity k (which may be assumed constant). Because of the chemical reaction occurring within the porous pellet, heat is generated at a constant rate of Se cal/em s. Heat is lost at the outer surface of the pellet to a gas stream at a constant temperature T, by convective heat transfer coefficient h. Gas bemperature T, Figure I. Sphere with internal heat generation Answer the following questions (a) Make a list of assumptions that apply to the above situation. (b) Set up the differential equation by making a shell energy balance. Show the units for all variables that are used. (c) Specify the proper boundary conditions. (d) Integrate the differential equation with the above boundary conditions to obtain an expression for the temperature profile, and make a sketch of the function profile T(r) (e) What is the limiting form of T(r) when h co? (f) What is the maximum temperature in the system? (g)…
PROBLEMS 1.1. In the table below, a number in the top row represents the pressure of a gas in the bulb of a constant-volume gas thermometer (corrected for dead space, thermal expansion of bulb, etc.) when the bulb is immersed in a water triple-point cell. The bottom row represents the corresponding readings of pressure when the bulb is surrounded by a material at a constant unknown temperature. Calculate the ideal- gas temperature T of this material. (Use five significant figures.) PTP, kPa P, kPa 133.32 99.992 33.331 66.661 102.37 204.69 153.54 51.190
Draw what the heating curve would look like for a sample of liquid water at 35degC heated to steam at 120degC. Label your starting temperature, ending temperature, boiling point and the states of matter along the line of the curve. Use the graph to calculate the total energy required to raise the temperature of 225g of water from 35degC to 120degC. (Hint: Only 3 calculations are required.) deltaHvap = +40.7 kJ/mol. c(water) = 4.18 J/g deg. c(steam) = 2.02 J/g degC *
Presents the diagram of the problem, necessary formulas, clearance and numerical solution: A small hole in a furnace acts like a blackbody. Its area is 1 cm2 and its temperature is the same as that inside the oven, 1,727 ◦C. How many calories are radiated out of the hole each second?
How many particles are present in a closed container if the energy it contains is 95859.14 J, and the diatomic oxygen gas is moving at a velocity of 67.56 m/s? Use only the whole number for the value of atomic mass unit. Express your answer in proper scientific notation.
The relation between resistance R and temperature T for a thermistor (a device that measures temperature) closely follows R = Ro e[Beta (1/T - 1/To)] where R is the resistance in ohms measured at temperature K, and Beta is a material constant. What are the units of Beta and Ro? Clearly show how you decided on your answer.