Circuit Diagram: E 12V Apparatus: R1 20 1. DC Power Supply. 2. Resistors. 3. Digital Multimeter. 4. Connecting wires. 100 Figure (1) Procedure: 1. Connect the circuit shown in Figure 1. 2. Set the power supplies at E₁ = 12V & E;=6V. 3. Measure the current and voltage at R₂. 4. Set the power supplies at E,- 12 V & E:-(S.C). 5. Measure the current and voltage at R.. 6. Set the power supplies at E₁-(S.C) & E-6V 7. Measure the current and voltage at Rs. 8. Record the results in table (1).

Circuit Diagram: E 12V Apparatus: R1 20 1. DC Power Supply. 2. Resistors. 3. Digital Multimeter. 4. Connecting wires. 100 Figure (1) Procedure: 1. Connect the circuit shown in Figure 1. 2. Set the power supplies at E₁ = 12V & E;=6V. 3. Measure the current and voltage at R₂. 4. Set the power supplies at E,- 12 V & E:-(S.C). 5. Measure the current and voltage at R.. 6. Set the power supplies at E₁-(S.C) & E-6V 7. Measure the current and voltage at Rs. 8. Record the results in table (1).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

what is the use of DC/DC tension converter DC/DC booster MT3608
Q1: Draw the d.c load line for the circuit shown in figure. NO SIGNAL VBB Vcc= 12.5 V www Re=2.5 k2
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.
In the Figure below if volts/div-5 then Vims is (in volt) Selectone. O a. 2.6 O b.12.75 O c. 9.19 O d.18
1- spark gaps testing method is applicable for testing 2- the electrical circuit that we use to measure high voltages and is not affected by frequency change 3- We can say high voltages if exceed ------------ V (Alternating voltages) 4- Transient voltages which are caused over voltages be in two forms 5- High voltages can be generated for testing in three ways ------
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di i v2 = VmSin ot RL Vs(N V1 Vo + V3 = VmSin ot D2 Full-wave rectifier- Circuit operation during positive half cycle 460 V 207 V 325.3 V None of the above ell ell
The voltage regulation can be equal to zero :when .The t and current is not too highO .The p.f. is leading p.f. for any possible current O .The p.f. is lagging p.f. for rated current O
a) Graphically show the differences between alternating current voltage (A.C) and direct current voltage (D.C). What are the advantages of A.C compared to D.C?
Calculate the peak-to-peak inductor current ripple (in amperes) of a Buck converter assuming it operates in continuous current conduction mode. Circuit parameters are: Input voltage Vdc = 38 V, output voltage Vo = 17 V, PWM frequency fpwm = 50 kHz, inductor value 328 µH and capacitor value C = 10 µF. is S iL L I₂ Vac VA D VL ic C R₁ Please specify your answer in units of A to 2 decimal places. V
ZEV * OMANTEL I. A moodle1.du.edu.om Question 2 Not yet answered Marked out of 2.00 P Flag question A buck converter produces an output voltage of 100 V across a 100 Ohm load resistor. The output voltage ripple is 0.5 %. The output current ripple is 2 A. The dc supply is 200 V. The switching frequency is 1 kHz. The value of the inductor is: Select one: O a. 25.00 milli Henry b. 35.25 micro Henry O c. None of the above d. 88.55 micro Henry O e. 75.15 nano Henry Previous page Next page
Q1) The buck converter has an input of 50 V and an output of 25 V. The switching frequency is 100 kHz, and the output power to a load resistor is 125 W. Determine: (a) the duty ratio. (b) the value of inductance to limit the peak inductor current to 6.25 A. (c) the value of capacitance to limit the output voltage ripple to 0.5 percent.
What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mA