An open system is often referred to as control volume, which is a properly selected region in space in which mass and energy can flow across the boundaries as figure 1.2. The boundary of a open thermodynamic system is called the control surface Across the Boundaries E = Yes F 0 = Yes w =Yes Control surface ass YES W CONTROL VOLUME energy YES Figure 1.2. A cooling/heating radiator is an example of such a system – give two more examples of such a system.

An open system is often referred to as control volume, which is a properly selected region in space in which mass and energy can flow across the boundaries as figure 1.2. The boundary of a open thermodynamic system is called the control surface Across the Boundaries E = Yes F 0 = Yes w =Yes Control surface ass YES W CONTROL VOLUME energy YES Figure 1.2. A cooling/heating radiator is an example of such a system – give two more examples of such a system.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.63P

See similar textbooks

Similar questions

2. I just need the graph of this. A certain ideal gas (unknown) inside a close piston-cylinder assembly undergoes a set of processes that composed of Isothermal expansion from State point 1 to state point 2, Isometric heat rejection from state point 2 to state point 3, and Isentropic compression from state point 3 back to the initial condition. If the maximum pressure is 3000kPa and maximum and minimum volume is 200cm3 and 50cm3
Thermodynamics Answer the following problem with complete solutions. Write legibly A gas goes through the following thermodynamic processes: A to B: constant-temperature compression; B to C: constant-volume cooling; C to A: constant-pressure expansion. The pressure and volume at state C are 1.4 bars and 0.028 m^3, respectively. The net work during the C-to-A process is 10.5 kJ. What net work is derived from one complete A-B-C cycle?
(9 blanks) Derive the work done of an ideal gas undergoing isothermal expansion at temperature T1 if the volume changes from V1 to V2. Express in terms of P1 and P2. V2 W = V1 Where: p= TV By substitution: V2 dv W = vị V Applying the rules of integration, the word done will become W= In| Using: P1V1 = nRT & P2V2 = nRT The work done in terms of pressure is expressed as W = In >
A question on thermodynamics regarding state variables: Q1) I have a simple piston/cylinder system containing an ideal gas at initial pressure Pi that is in a constant temperature surrounding. I compress the cylinder isothermally to 1/20th its initial volume and then expand it isothermally back to its original volume. What is the final pressure? Suppose I compress and expand it adiabatically, what is the difference in the final pressure then?
number 1 A food product containing 80% moisture content is being frozen. Estimate the specific heat of the product at -8 ° C when 80% of the water is frozen. The specific heat of the dry product is 2 kJ / (kg ° C). It is assumed that the specific heat of water at -10 ° C is the same as the specific heat of water at 0 ° C, and that the specific heat of ice follows the function Cp es = 0.0062 T Frozen + 2.0649. Cp of frozen product = kJ / kg ° C.
Q1. (Reading: Çengel and Boles, Thermodynamics: An Engineering Approach, 8th Ed., Pages 307-311) The amount of energy waste by a refrigerator increases by a number of malpractices. For example; opening the refrigerator door frequently will increase energy waste as the warmer air outside replaces the cool air inside. It is also not recommended to place the hot foods into the refrigerator before cooling them to the room temperature. Imagine a typical household refrigerator with an internal temperature of 4 °C. The refrigerator has a coefficient of performance of 1.4. The internal dimensions of this refrigerator are 186 cm (height) x 84 cm (width) x 75 cm (depth). The half of the refrigerator volume is used for storing food items. The air filling the other half of the refrigator volume contains 0.004 kg moisture/kg air on average. While the moisture content of the air in the kitchen is 0.01 kg/kg air, the temperature and pressure in the kitchen are 23°C and 97 kPa, respectively. Assuming…
3. Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20 °C, TL=5200 °C. The density, conductivity and specific heat of the material are p 800 kg/m³, k=200 W/m.K, and cp=2500 J/kg.K, respectively. Also, r= 520 cm and L=1040cm. To TL L To
Air treated as an ideal gas and having a specific heat at constant volume Cv=1200 j/kg.K undergoes a process. During this process, heat is observed to exit the system with an amount of 10 kJ while work is provided to the system with an amount of 23 kJ. If the initial temperature of air was 20 C, what is the final temperature of air if the mass of air undergoing the process is 0.3 Kg. Select one: O a. 59.5 C O b. 48.73 C O c. 63.4 C O d. 56.1 C
A liquid reactant solution is pumped through a pre-heater before entering a reaction vessel. The solution enters the pre-heater at 25 °C and must enter the reactor at 45 °C. The flow of the reactant solution is 1500 mL per minute. The density of the reactant solution is 0.91 g-cm3 and the heat capacity is 1.75 Jg1.K1. ASsume there is no heat loss in the pre-heater or between the pre-heater and the reactor. a. Draw a schematic of the pre-heater, detailing all mass and energy flows. b. Clearly define a system boundary. c. Write the general energy balance, and a simplified energy balance stating all assumptions that apply to this problem. d. What is the minimum power rating required for the pre-heater?
A certain ideal gas (unknown) inside a close piston-cylinder assembly undergoes a set of processes that composed of Isothermal expansion from State point 1 to state point 2, Isometric heat rejection from state point 2 to state point 3, and Isentropic compression from state point 3 back to the initial condition. If the maximum pressure is 3000kPa and maximum and minimum volume is 200cm³ and 50cm', analyze the problem and perform the following: a. Draw and label the graph of this set of processes in the P-V and T-S diagram showing the state point numbers and energy directions. b. From the known ideal gases as shown in Table 1.0, select the best suited ideal gas to attain the processes stated if the lowest pressure is limited to 629.8kPa. Assume a constant specific heat. c. For the selected ideal gas from b, compute the work of compression (kJ/kg), work of expansion (kJ/kg), and heat rejected (kJ/kg) Table 1.0: Ideal gas specific heats of various common gases Gas constant, R Gas Formula…
Drag and Drop the correct answers in the blanks. A mass mis hanging from the end of a vertical spring that has a spring constant k. The equilibrium position of the mass, yo, is The total potential energy of the mass when it is displaced by s from the equilibrium position is given by Y. is zero + U(s) = ks + positive * negative 1 1 ks+ 21 + U(s) ks² + mgyo %3D U(s) mgyo
number 1 A food product containing 75% moisture content is being frozen. Estimate the specific heat of the product at -10° C when 85% of the water is frozen. The specific heat of the dry product is 2 kJ / (kg ° C). It is assumed that the specific heat of water at -10 ° C is the same as the specific heat of water at 0 ° C, and that the specific heat of ice follows the function Cp es = 0.0062 T Frozen + 2.0649. Cp of frozen product = kJ / kg ° C.