A steel pipe of 12-in. outer diameter is fabricated from 1/4-in.-thick plate by welding along a helix that forms an angle of 45° with a plane parallel to the axis of the pipe. Knowing that the maximum allowable tensile stress in the weld is 9 ksl, determine the largest torque that can be applied to the pipe. 12 in. +in. The largest torque that can be applied to the pipe is [ kip-in.

A steel pipe of 12-in. outer diameter is fabricated from 1/4-in.-thick plate by welding along a helix that forms an angle of 45° with a plane parallel to the axis of the pipe. Knowing that the maximum allowable tensile stress in the weld is 9 ksl, determine the largest torque that can be applied to the pipe. 12 in. +in. The largest torque that can be applied to the pipe is [ kip-in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel pipe of 12-in. outer diameter is fabricated from 14-in.-thick plate by welding along a helix that forms an angle of 45° with a plane parallel to the axis of the pipe. Knowing that the maximum allowable tensile stress in the weld is 12 ksi, determine the largest torque that can be applied to the pipe.
Draw Mohr's circle that describes each of the following states of stress. (b.) 12 ksi 6 ksi .8 ksi
Question 2. The hollow steel shaft has a diameter of 65 mm and thickness of 5mm, is subjected to a torque and moment produced by a 3 kN force which is 15 mm from the centre of the shafts cross section. The shafts have the same centroid. a. Using Mohr's circle, determine the principal stress, maximum in-plane shear stress and average normal stress in the at point J and K. b. If the weld has a 30° at point J, what is the maximum shear stress the weld has to with- stand. K 700 mm F=3kN 15 mm c. Determine the maximum bending stress if the hole in the cross section area is now off centre by 2 mm in the x and y direction.
(b) A solid rectangular shaft of cross-section 80 mm × 50 mm is welded by a 5 mm fillet weld on all sides to a flat plate with axis perpendicular to the plate surface. Find the the maximum torque that can be applied to the shaft, if the shear stress in the weld is not to exceed 85 MPa. 11
2. A carbon steel ball with a 30-mm diameter is pressed against a flat carbon steel plate with a force of 20 N. Determine the maximum shear stress, and the depth in the plate at which it will occur.
Determine the diameter (in mm) of the largest circular hole that can be punched into a sheet of polystyrene 6.19 mm thick, knowing that the force exerted by the punch is 41.2 kN and that a 51.2-MPashearing stress is required to cause the material to fail.
A steel pipe of 300-mm outer diameter is fabricated from an 8-mm-thick plate by welding along a helix that forms an angle of 20° with a plane perpendicular to the axis of the pipe. Knowing that a 250-kN axial force P and a 12-kN-m torque T. each directed as shown, are applied to the pipe, determine the normal and in-plane shearing stresses in directions, respectively, normal and tangential to the weld. T The normal stress is - The shear stress is- Weld 20⁰ 8 mm MPa MPa.
The steel pressure tank shown has a 751 mm inner diameter and a 9.1 mm wall thickness.Knowing that the butt-welded seams form an angle ? = 50° with the longitudinal axis of thetank and that the gage pressure in the tank is 1.56 Mpa.a. Determine the normal stress perpendicular to the weldb. Determine the shearing stress parallel to the weld
Question 1 B 900 mm 80 mm -40 mm T A The magnesium tube is bonded to the steel rod. Part A If the allowable shear stresses for the magnesium and steel are (Tallow)mg = 45 MPa and (Tallow)st = 75 MPa, respectively, determine the maximum allowable torque that can be applied at A. Part B If a torque T of 5 kN-m is applied to end A, determine the maximum shear stress in each material.
This is my Question... Determine the vertical displacement of joint C . EA is constant Determine the Vertical Displacement of the Joint C. EA is Constant Thank You Very Much
For a given maximum average shear stress, determine the factor by which the torque-carrying capacity is increased if the half-circular section is reversed from the dashed-line position to the section shown. The tube is 0.1 in. thick.
A 60 mm- В 90 mm- 100 mm C 4 kN 80 mm D 140 mm