can you please find solution for this question Q3.shaded area) at a flow rate of 320 liters/min.JA shell and tube heat exchanger has the cross-section shown below. Crude oil (specific gravity, sg = 0.86) at 10°C flows through the shell passage (theS Calculate the Hydraulic Diameter in units of mm.b)Calculate the Reynolds number for the Crude-oil flow.c)Determine the flow regime (laminar, transitional, or turbulent).45 mmD = 5.5 mmTypical of 845mm

To Calculate : 1). Hydraulic Diameter in mm. 2). Reynolds number of Crude oil. 3). The flow regime.…

A shell and tube heat exchanger has the cross-section shown below. Crude oil (specific gravity, sg = 0.86) at 10°C flows through the shell passage (the 93. shaded area) at a flow rate of 320 liters/min. a) Calculate the Hydraulic Diameter in units of mm. b) Calculate the Reynolds number for the Crude-oil flow. c) Determine the flow regime (laminar, transitional, or turbulent). 45 mm

A shell and tube heat exchanger has the cross-section shown below. Crude oil (specific gravity, sg = 0.86) at 10°C flows through the shell passage (the 93. shaded area) at a flow rate of 320 liters/min. a) Calculate the Hydraulic Diameter in units of mm. b) Calculate the Reynolds number for the Crude-oil flow. c) Determine the flow regime (laminar, transitional, or turbulent). 45 mm

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.4P: 5.4 Evaluate the Stanton number for flow over a tube from the following data: , , , , .

See similar textbooks

Similar questions

1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm to water (p= 62 11m/ft²³) Ignore any changes in Kinetic or potential energy and Tassume isothermal flow C.e. internal energy is constant, this is the normal assumption we make when analyzing fluid flows in piping systems). Apply the energy balance only across the pump with full energy Balance and simlifying to solve for the pump, Starting head symbolically. Then begin careful of units, Solve for pump head in feet. GIVEN: 35psi 500 gpm p=62 1bm/3 XA. 10.5 A B. 100.8 ft C. 50.1 ft D. 80.7f 35 500 62 (32.2) + 2(32.2) 35 + 500
Q-2 ) ) A boiler house has natural draught chimney of 20 m height. Flue gases are at temperature of 380°C and ambient temperature is 27°C. Determine the draught in mm of water column for maximum discharge through chimney and also the air supplied per kg of fuel. Ans. [11.77 mm of water, 11.32 kg/kg of fuel
A2: FLUID FLOW, FLOW RATE & PRESSURE DROPProblem:4. Determine the average velocity in m/s for water flow in a 2 in diameter pipe, Schedule 40 chlorinated polyvinyl chloride (CPVC) pipe (2.375 in outside diameter and 2.047 in inside diameter) carrying cold water at a volumetric flow rate of 40 gpm.
B) Water flows in 50 mm pipe, 100 mm long whose roughness is 0.013 mm. If the pressure drop across this length is not exceed 50 kpa. What is the water velocity, p=1000 kg/m³. p=0.001 pa.s.
It requires a specific displacement before the flow become fully developed. Entry length a. depends only on diameter of pipe for turbulent flowb. depends on Reynolds number and diameter for turbulent flowc. and diameter ratio varies in turbulent flowd. All of these
Hello! This is my last question remaining that's why im posting these 2 question together, I hope you can answer both thank you so much! :(( 1. The length of a pipe is 168 meters. If the pressure drop is 50 kPa for every 30 meters. What is the total pressure drop? a. 250b. 280c. 330d. 410 The correct answer here is b. 280. I just need the complete solution thank you! 2. What is the flow rate through a pipe 4 inch diameter with water velocity of 11 ft/sec.a. 0.0272 cu m/sb. 0.0185 cu. m/sc. 0.2345 cu. m/sd. 0.0345 cu. m/s The correct answer here is a.0.0272 cu m/s. I just need the complete solution thank you!
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa
long. The inlet water temperature is 10 C, and the tube wall temperature is 15 C water temperature. k 0.585, Pr= 9.4, u= 1.31x10*,p= 992kg/m, CP= 4195 j/kg. higher than the water temperature all along the length of the tube. What is the exit %3D Q5//answer one of the following branches e jall al je yal A) cast iron pipe (k=75w/m. °C) air flows inside this pipe at 300°C the inner diameter is 0.06 m, the outer diameter 7cm,it is covered with insulation type glass wool with thick 4cm. with k= 0.055w/m.°C .the ambient temperature 6 °C by free V3. convection with heat transfer coefficient (20w/m2. °C) the heat transfer inside the pipe is 65 w/m?. °C. length of tube (L-2) determine 1-the heat lost from the hot air 2-the temperature drop across the pipe shell 3-the temperature drop across the insulation. 344 14. 1256 and B) Fill the blanks: of the 1. The thermal resistance of a medium depends on medium. 2 All law. pes of convection are governed by 10000, the flow is
Q: Pressure drop in slug flow-M. A light oil and a gas are flowing upward in a vertical tube of 4.0-in. I.D. at superficial velocities of L/A 1.2 ft/sec and G/A = 4.8 ft/sec, = respectively. The viscosities of the oil and gas are 15.6 and 0.038... Posted one year ago
Water is pumped through a horizontal, smooth circular pipe at a bulk velocity of 0.4 m/s. The pipe has an internal diameter of 250 mm and a total length of 1600 m. The pipe flow is fully-developed. The shear viscosity of the water is 1 mPa.s. g) Calculate the power required to pump the water if the fluid flow is laminar. Provide your answer to two decimal places.
A 0.5-inch diameter water pipe is 18 m long and delivers 19 L/min. What fraction of this pipe is taken by the entrance region?[Ans. LE /L=1.7%]
01) Example: Find the velocity at the pipe center. water D-3" 0.0 (stag.) Hg (S-13.6)