A piston-cylinder assembly contains a two-phase liquid-vapor mixture of water with an initial dryness fraction of 50%. The mass of the piston is 15 kg with a diameter of 10 cm. The surroundings exert a pressure of 1 atm in the piston, Heat is added to the system under the isopiestic process until the piston hits the stops. The final condition of the steam is saturated vapor. Determine the work in kVW if the mass of the mixture is 22.544 kg/s.

A piston-cylinder assembly contains a two-phase liquid-vapor mixture of water with an initial dryness fraction of 50%. The mass of the piston is 15 kg with a diameter of 10 cm. The surroundings exert a pressure of 1 atm in the piston, Heat is added to the system under the isopiestic process until the piston hits the stops. The final condition of the steam is saturated vapor. Determine the work in kVW if the mass of the mixture is 22.544 kg/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Required information Problem 04.038 - Energy balance for water in a piston-cylinder device NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. An insulated piston-cylinder device contains 3.5 L of saturated liquid water at a constant pressure of 175 kPa. Water is stirred by a paddle wheel while a current of 8 A flows for 45 min through a resistor placed in the water. One-half of the liquid is evaporated during this constant-pressure process and the paddle-wheel work amounts to 400 kJ. 11,0 consta Problem 04.038.a - Find source voltage Determine the voltage of the source. Use data from the steam tables. (Please provide an answer before moving on to the next part) The voltage of the source is V.
Pls solve accurate and fast A 1-kg steam-water mixture at 1.0 MPa is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPa and the temperature to 400: Determine the heat added
A rigid closed tank contains refrigerant 134a wnich is initally a two- phase liquid - vapor mxiure with a temperaflure of D'c and a quality of Ce0%. An electrical resistor nistalled inside the Fank transfers until the tank contains only saturated vapor. if the tank is well - insulated and the mass of the Cefrigerant is 1.5 kg, determıne the time it takes for the process to be completed in seconds using 5 signifigant Agures
Q2) Steam at a pressure of (5 bar) passes into a tank containing water where it gets condensed. The mass and temperature in the tank before the admission of steam are (50 kg) and (20°C) respectively. Calculate the dryness fraction of steam as it enters the tank if (3 kg) of steam gets condensed and resulting temperature of the mixture becomes (40°C). Take water equivalent of tank as (1.5 kg). (25 marks)
v Question Completion Status: QUESTION 11 50 kg of Refrigerant R134 are in the state of Saturated mixture at a pressure of P1a180 kpa. The quality x is equal to 0.2. It undergoes an expansion process to a superheated state of Py- 140 KPa and a temperature Ta-30°C. a) What is the initial temperature of the mixture. b) use the quality x to find the specific volume vy of the mixture (so called vavg) and the total volume Vy. Find the specific enthalpy of the mixture hy and conclude the total enthalpy H. d) Find the variation of enthalpy AH-H,-H, between the two states. e) Find the variation of volume between the two states.
Mr Zul operates a hot plate. He places a closed, rigid container of volume 0.5 m3on the hot plate. Initially, the container holds a saturated mixture with quality ofvapour of 0.5, at a pressure of 100 kPa. After heating, the pressure in the containerincreases to 150 kPa.a) Calculate the mass of vapour at the initial and final states (in kg).b) If heating is allowed to continue, find the pressure (in kPa) when thecontainer holds only saturated vapour.c) Sketch the T – v diagram for this system.
Outside air at 30 C drybulb & 25 C wetbulb temperature flowing at a rate of 25,000 liters/min is mix with colder air at 20 C drybulb & 18 C wetbulb temperature flowing at a rate 70,000 liters/min. After mixing , the mxture undergoes sensible heating up to 40 C . Compute the heating needed in kW. Plot the process on the Psychrometric chart and label it completely.
Please
Outside air at 30 C drybulb & 25 C wetbulb temperature flowing at a rate of 25,000 liters/min is mix with colder air at 20 C drybulb & 18 C wetbulb temperature flowing at a rate 70,000 liters/min. After mixing , the mxture undergoes sensible heating up to 40 C . Compute the heating needed in kW. Plot the process on the Psychrometric chart and label it completely. Can you upload the chart also?
2. 10kg of H₂O in a 1.5m³ tank is initially at 200°C heat loss causes a decrease in temperature to 150°C. find: a. Phase 1 and 2 b. Internal Energy at 1 and 2 c. Heat loss if this system is stationary d. Heat loss if the body moving at velocity of 5m/s and assuming the mass of the empty tank negligible. Tonk A contains 2-kg steam a
Air as an ideal gas is contained in a piston/cylinder system constrained by a non-linear spring. Initially the gas in the cylinder is at 100 kPa, which is balanced by the atmospheric pressure outside of the cylinder (the weight of the piston is negligible). The force on the spring at the start is zero. The spring force is F=kx². k=600. kNt/m². The cross-sectional area of the piston is 1 m², the initial volume is 1 m³, and the initial temperature is 300 K. Heat is added until the volume of the gas has expanded to 1.5 m³. Find: (a) The work done by the gas on the face of the piston (kJ). (b) The final temperature (K). (c) The amount of heat added (kJ). Hint: This problem is easiest if you calculate the spring work and the atmospheric work separately. Air V₁=1.0 m³ Piston Area = 1.0 m² T₁=300 K P₁=100 kPa Atmospheric P on upper piston face= 100 kPa
A conduit connects two receptacle of different size. A valve is used at eachend which can be opened or closed. The first receptacle contains 300 liters of air at 4,200 kPa, 82C. The second receptacle contains air at 75kPa, 9C. Calculate the volume of the second receptacle if after the valve was opened and the properties of the mixture were 2400kPa for the pressure, and 52C for the temperature.