A pipe is being designed to carry a fluid at a pressure of 193 MPa. In order to allow sufficient fluid flow, the internal diameter of the pipe cannot be less than 3.6 mm. Due to space constraints, the outer diameter of the pipe cannot be greater than 12.5 mm. The maximum shear stress allowed in the pipe wall is 507 N/mm². Calculate the minimum outer diameter that the pipe can have. Give your answer in mm.

A pipe is being designed to carry a fluid at a pressure of 193 MPa. In order to allow sufficient fluid flow, the internal diameter of the pipe cannot be less than 3.6 mm. Due to space constraints, the outer diameter of the pipe cannot be greater than 12.5 mm. The maximum shear stress allowed in the pipe wall is 507 N/mm². Calculate the minimum outer diameter that the pipe can have. Give your answer in mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are asked to calculate the pressure drop in a straight pipe. Air of density 1.225 kg/m³ is flowing through the pipe. The diameter of the pipe is 25 mm. The velocity of the flow is 1 m/s. The viscosity of air is given as 1.85 x 10-5 Pas. From this information the Reynolds number was calculated to be 1655. Determine the Head drop if the pipe is 100 m in length. Hint: For laminar flow the fanning friction factor can be calculated as 16/Re 4 fLū² hs 2gD 2 Answer: Answer
A small capillary with an inside diameter of 2.22 x 10-3m and a length 0.317m is being used to continuously measure the flow rate of a liquid having a density of 875 kg/m3 and viscosity of 1.13 x 103 Pa-s. The pressure drop reading across the capillary during flow is 0.0655m water (Density is 996 kg/m3). What is the flowrate in cu.fps?
If I have a cylindrical plug of sandstone 1 m long with a diameter of 3 cm, and with permeability 100 mD, and want to inject water at 3 atm (absolute) into the plug, what rate would be needed if the flow discharges to atmospheric pressure
A patient receives IV fluid through a needle of radius 0.200 mm and length 2.0 cm. The density of the IV fluid is 1050 kg/m3 and it has a viscosity of 2.7 x 10-3 Pa s. The bag supplying the IV is 1.30 m above the patients arm. The blood pressure in the patient’s vein is 80 mm Hg. what is the gauge pressure inside the needle? What is the gauge pressure in the vein? What is the flow rate of the IV?
1) The velocity profile of a viscus fluid over a plate is parabolie with vertex 25 em from the plate ,where the velocity 125 cm/s. calculate the velocity gradient and shear stress at distance of (0, 5, 15 and 25 cm) from the plate given the viscosity of the fluid =7 poise ? Also draw the figure explain the relationship between the velocity gradient and shear stress. Take velocity profile for parabolic equation, (v = ay + by + c)
Please answer me in 30min plz urgent need Water enters a 6cm internal diameter thin walled pipe with 10 °C and exits at 30°C. The flow rate is 2.3lit/ min. Find the length of the pipe if the outer surface of the pipe has a constant surface temperature of 90 °C (Tolerance limit+0.2 m).
A fluid passes passes through a pipe with the following condition Fluid: - 1.61 x 10-4 Kinematic Viscosity Density - 2*/ma Specific Heat = 30 000 '/rg K Pipe: Inner Diameter = 50 mm Outer Diameter = 60mm Length = 11 m 3D Thermal conductivity = 17 "/mx Heat Transfer coefficient of water = 99 Compute for Prandit and Nusselt Number
QUESTION 9 A liquid cooled heat sink for a smartphone is sketched in Figure Q9. It uses water of density p = 997 kg m-3 and kinematic viscosity v = 1.19 x 10-6 m²-s-1 that runs in the x₁ direction through each of the five tubes of constant diameter D₁ = 5 mm and length Lx1 = 20 mm. It is supplied by a U = 0.017 m-s-1 uniform water inflow. Use Blasius' skin friction coefficient Cf = 0.664 / Rex1 0.5 to calculate the total skin friction drag force imparted by the flow on the heat sink walls. Calculate your answer in microNewtons, to one decimal place and enter the numerical value only. 1 microNewton = 10-6 Newtons. Partial credit is awarded for a reasonable approximation to the correct numerical answer. Lx₂ X2 Lx1 X1 Ő ve Heat Flux (9) (a) Figure Q9: Schematic of a liquid cooled heat sink LX3 4
Simulation of laminar gas flow in the pipe with Ansys Fluent Task: 1. Calculate velocity distribution in y axis at inlet and outlet of the pipe. Submit it as a chart. 2. Calculate velocity distribution over the pipe length. Submit it as a chart. Figure. pipe geometry L, m = 16 R, m= 0.15 Inlet velocity, m/s= 0.08 Gas= Oxygen Need proper solution like pdf file, don't need steps by steps. If you can can do it through ansys fluent. Write proper solution on word file or pdf.
Problem 3: IV Bag A 3 cm long needle at the bottom of a tube connected to an IV bag is used to inject a 125 mL of saline solution located h = 70 cm above the needle over a one hour period. The viscosity of the saline solution is 1.1 mPa.s and its density is 970 kg/m³. You may assume the resistance to flow and fluid speed in the bag and the tube is negligible - only the resistance across the needle needs to be taken into account. A. If the vein's gauge pressure is 5 mmHg, what will be the difference in the input and output pressures across the needle in both mmHg and Pa? B. What is the flow rate of the fluid, in S.I. unis? C. What is the radius of this needle in mm?
Q:- A solid circular cylinder of diameter 100 mm and length 200 mm slides inside a vertical smooth pipe that has inside diameter 100.5 mm. The small space between the cylinder and the pipe is lubricated with an oil film that has viscosity 3 N.s/m2.The cylinder weight 20 N and concentric with the pipe as it falls .Find the rate of the changer in velocity of the cylinder? Pbe Cylinder O Flm
The thrust of a shaft is taken by a collar bearing provided with a forced The lubrication system maintains a film of oil of lubrication system. orm thickness between the surface of the collar and the bearing The mal and intemal diameters of collar are 16 and 12 cms. respectively. The thickness of oil film is 0.02 ems. and coefficient of viscosity is 0.91 naise. Find the horse-power lost in overcoming friction: when the shaft is notated at a speed of 350 E.p.m. Skult