6-22. The beam is subjected to a uniform live load of 1.2 kN/m, a dead load of 0.5 kN/m, and a single live load of 40 kN. Determine (a) the maximum positive moment created by these loads at E, and (b) the maximum positive shear at E. Assume A and C are rollers, and B is a short link. AI - 4 m B CI 4m 4m Prob. 6-22 E -4 m XD

6-22. The beam is subjected to a uniform live load of 1.2 kN/m, a dead load of 0.5 kN/m, and a single live load of 40 kN. Determine (a) the maximum positive moment created by these loads at E, and (b) the maximum positive shear at E. Assume A and C are rollers, and B is a short link. AI - 4 m B CI 4m 4m Prob. 6-22 E -4 m XD

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ane AB P6-3. Draw the free-body diagrams of the boom ABCDF and the stick FGH of the bucket lift. Neglect the weights of the members. The bucket weighs w.The two-force members are BI, CE, DE and GE. Assume all indicated points of connection are pins. E G F D Ро-3
*3-4. The bearing consists of rollers, symmetrically confined within the housing. The bottom one is subjected to a 125-N force at its contact A due to the load on the shaft. Determine the normal reactions NB and Nc on the bearing at its contact points B and C for equilibrium. 40 B Ng- 125 N Prob. 3-4
Bar AC supports two 400-N loads as shown. Rollers at A and C rest against frictionless surfaces and a cable BD is attached at B. Determine (a) the tension in cable BD, (b) the reaction at A, (c) the reaction at C.
1-74 The W8x 67 wide- flange A- 36steel Column Con bbe assumed fired at is based and pinned at t top. Determinie the largiest axial load, P that Can be Capplied without Causing e it to buckle 25ft
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the tension at wire BD. E 4 m 3 m 2 m 2 m O 1.95kN O 1.64kN O 0.91kN O 1.29KN o o oO
iz: QUIZ (MODULE 5). A continuous beam has a loading shown. Assuming constant flexural rigidity (El). 50KN 35KN 70KN 40KN 2m 3m 2m 2m 3m 2m B 2 C 3 D 4. 5m 7m Determine the following: a. Moment at 3 or C (kN-m: write positive or negative) b. Moment at 2 or B (kN-m: write positive or negative) C. Reaction at 1 or A (kN: positive value only) d. Reaction at 2 or B (kN: positive value onlv) e. Reaction at 3 or C(KN. positive value only)
Find the tension in the Active tension bracing in the center bay (hint: again, there is no need to find reactions). E B O с D 16' -12'- H 8k 12' G 2k 12' F 4k 3k
Draw the Influence Line for the for the truss member KJ and JE. A L 1080 B K 3882 C J I 8880 E D 8 ft 8 ft 8 ft 8 ft 8 ft - - H F -8 ft- 8 ft G ***
A solid 1.00-in.-diameter steel [G = 12000 ksi] shaft is subjected to the torques shown. Determine the rotation angle of pulley D with respect to the support at A. (1) 240 lb-ft 36 in. O-0.0653 rad O-0.0513 rad O-0.0415 rad O-0.0542 rad O-0.0316 rad B (2) 36 in. 215 lb-ft (3) 36 in. 110 lb-ft D
Determine the design ungke ( ) for strut AR o that the 400-b horintal force ham a component of S00 h directod from A towands CWhat is the component of fore acting akong member ART Take - 4.
What will be the fully plastic moment in the portal frame shown in figure? The frame has a uniform cross-section throughout. (Assume only combined mechanism.) 40 kN 20 kN B D 2 m-te- 2 m- 3. E
*2-16. Classify each of the structures as statically determinate, statically indeterminate, or unstable. If indeterminate, specify the degree of indeterminacy. The supports or connections are to be assumed as stated. roller pin fixed 8 bns Aanogque od tneno (a) A roller В Гoller rollerC (b) ol d no no A D pin roller B rollerC pin (c) Prob. 2-16