5. For the frame shown in the figure, determine the slope at A DA using Castigliano's Theorem. E = 29X10^3 ksi. Consider support D as fixed B. 12 ft -5 ft 12 k -5 ft- IBC = 900 in.* LAB= 600 in. ICD= 600 in.4 C D

5. For the frame shown in the figure, determine the slope at A DA using Castigliano's Theorem. E = 29X10^3 ksi. Consider support D as fixed B. 12 ft -5 ft 12 k -5 ft- IBC = 900 in.* LAB= 600 in. ICD= 600 in.4 C D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.6P: A beam with a sliding support at B is loaded by a uniformly distributed load with intensity q. Use...

See similar textbooks

Related questions

Q: A 11-ft-long, 6-ft-high rectangular tank open to the atmosphere is towed by a truck on a level road.…

A: A 11-ft-long, 6-ft-high rectangular tank open to the atmosphere is towed by a truck on a level road.…

Q: Determine the forces in each of the cable AC, BD, and BE. Also find the reaction forces at point O…

A: Given : The free body diagram is, The mass of cylinder is

Q: Consider the plate shown in (Figure 1). Figure 0.45 in. 3 in 0.54 in. 0.45 in. 1 of 1 > 0.5 in. 4.5…

Q: Problem 2: A solid circular drive shaft with a diameter of 0.5" transmits a torque of 200 in-lbf and…

A: To findWhat is the safety factor against yielding using the max. shear stress criterion?What is the…

Q: Find the lift force of potential flow a half cylinder.

A: Given : The flow is potential The pressure within the half-cylinder and the entire cylinder will be…

Q: Solve the following equation for x: erfc(x) = 0.125 Your Answer: 1.085

A: The complementary error function,

Q: A particle moves along a path defined by xy = 36 m² with a constant speed of 10 m/s. At x = 9 m…

A: To findDetermine the x and y components of the acceleration.GivenPath equation, Speed, Acceleration…

Q: Penny is adjusting the position of a stand up piano of mass mp = 155 kg in her living room. The…

Q: You are forced to pull a group of kindergarteners in a cart. You apply a horizontal force of F = 5…

A: Given-To Find-The acceleration of the cartThe normal force at A and BMath input error

Q: *3-32. The block is made of titanium Ti-6A1-4V and is subjected to a shortening of 0.06 in. along…

Q: E2.13 Assuming the lever in Figure E2.13 has negligible mass and remains within a small angle of the…

A: The lever is mass less

Q: A container is supported by three cables that are attached to a ceiling as shown. Determine the…

A: Given : The Tension in cable AB is

Q: The arm ABCD is subject to the forces shown. A. Find the sum of moments around point D (∑?? B.…

Q: 3.38 Water flows from a pressurized tank, through a 6-in.-diameter pipe, exits from a 2-in.-diameter…

A: Given:The diameter of the pipe, The diameter of the nozzle,

Q: 8 m/s y 100 mm -X 30⁰ B. 100 mm

Q: Draw a kinematic diagram for the following mechanisms and suggest a possible real life use for it.…

A: We'll calculate the degrees of freedom (DOF) for each mechanism to verify their mobility according…

Q: 6.1Complete the code please.

A: % Model parameters (can be moved to where needed in your script) a = 0.48; % prey's growth rate b =…

Q: A piston, 9 cm in diameter, is used to increase the internal pressure in a cylinder from 0 to 50…

A: The diameter of the piston is .The yield strength of the cylinder is .The fracture toughness of the…

Q: 2-97. Determine the magnitude and coordinate direction angles of the resultant of the two forces…

A: In first question,Two forces are acting at point A. It is required to determine the magnitude of the…

Q: A hydraulic press is used to apply 500 lbs of force to press fit an assembly. The cylinder has a 2"…

A: Given:The force applied by the hydraulic press, The diameter of the piston, The diameter of the rod,…

Q: Select an IPE profile for the loading case shown in the figure. Se- lect this IPE profile from the…

A: Given : The free body diagram is,

Q: turbo-charge Diesel cycle pv and ts diagram.

A: Diesel Cycle:A combustion process of a reciprocating internal combustion engine is known as Diesel…

Q: This question deals with a cylinder, which is upright. Here are the facts for the problem. Can you…

Q: Figure 0.4 m A 0.4 m B 60° 2 y=2.5x² 1 of 1 > Determine the mass of block B needed to hold it in the…

A: To find.determine the magnitude of the normal force it exerts on the surface.Determine the mass of…

Q: The rod AB shown below has a constant angular rotation of 5 rad/sec and is advancing upward along…

A: Given:find:Velocity and acceleration at point A

Q: A hydraulic cylinder with diameter 0.75 inch and a stroke length of 12 inches is used to lift a 20…

A: Given Data

Q: SOLVE STEP BY STEP IN DIGITAL FORMAT THANKS For the beam in shown in the figure, determine the…

A: For the solution refer below images.

Q: How does M2 fall into this?

A: Mass of the pulley is MAnd mass of the block is M2

Q: Water flows at steady state into a control volume at 240C, 1 bar, and 2³. It flows out at 3 bar and…

Q: 2. In Problem Set 3, Problem 2, we expanded superheated steam across a steady flow adiabatic turbine…

A: The inlet condition of the stream is,To find the adiabatic efficiency of the original turbine.

Q: a. Draw the free-body diagrams and write the differential equations of motion for the two masses in…

Q: The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and…

Q: A single angle section L152x152x19 of G40.21 300W is used as compression web member in a truss.…

A: The compressive resistance of the single angle section L152x152x19 is approximately 3.46 * 1012…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: 3.35B. For the section illustrated, find the second moment of area, the location of the neutral…

Q: Using the method of joints, calculate the force in each member of the truss shown. State whether…

A: as per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: Required information A model for the suspension of a vehicle is shown where the spring has stiffness…

A: Given: The spring stiffness is The unstreched lengh is

Q: solve, show all steps/solutions. include all asked for, no partial answer or ill dislike

A: Given that,The diameter of rod = d = 1 inchHence, radius of rod = r = 0.5 inchConsider following…

Q: The assembly consists of two 12-mm-diameter A992 steel rods AB and CD, a 20-mm-diameter 6061-T6…

A: To determine:The displacement of point Fgiven:The diameter of rods AB and CD is the diameter of rod…

Q: A pump with a volumetric displacement of 4 in^3/rev runs at 3600 rpm and produces 1500 psi. The…

A: The volumetric efficiency of the pump.Given:The volumetric displacement is .The angular speed of the…

Q: The two rods (A-B and B-C) shown in the left panel are connected by pins at A, B, and C. The cross…

A: The rod is subjected to a load of .Elongation- The elongation is defined as the measure of…

Q: Test Specimen Impact Energy (J or ft-lb) 4140 CF steel 48.5 ft-lb 6061 T6 Al Gray Cast iron 40 25…

A: Impact strength is nothing but a material's ability to withstand sudden applied forces or shocks…

Q: Compute the stress in the bar.

A: Here, is strain developed in the bar. is compressed length. is initial length of the bar.. is…

Q: Describe the cooling of a peritectic alloy with the concentration CO and sketch the microstructure…

A: The given figure is-

Q: A homogeneous, 1.2 m wide, 2.1 m long rectangular gate weighing 100 kg is held in place by a…

Q: 7. A 700. N skateboarder tips the front of the board up using an uneven distribution of weight as…

A: Given:The weight of the stake-boarder, The mass of the state board,

Q: An open-ended can 0.2m tall is originally full of air at 20°C. It is now immersed in water upside…

Q: For the given loading, determine the force in members HI, FI, and EF of the truss and state if the…

Q: Examine your crystal models and find: (a) the number of different (non-parallel) close - packed…

Q: 3) ANS. Two particles, A & B, move along parallel rectilinear paths. At t=0 the particles are…

Question

5. For the frame shown in the figure, determine the slope at A DA using Castigliano's Theorem.
E = 29X10^3 ksi.
Consider support D as fixed
12 ft
5 ft
12 k
5 ft
IBC= 900 in.4
LAB= 600 in.4
ICD=600 in.4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the given variable and fine

VIEW

Step 2: Calculating the reaction and moments

VIEW

Step 3: Calculating the reaction and moments

VIEW

Step 4: calculating the slope at A

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the following values in the given beam above: L1=6m L2 = 2 m L3 = 4 m L4=3m L5=2 m L6=1m W1 = 90 kN/m W2 = 30 kN/m P = 50 kN M = 60 kN-m Point E is an internal hinge W1 B L2 L3 2 m E W2 L5 L6 H
3. Determine the displacement and slope (i.e. 0) at the load point for the stepped beam shown in the following figure. Also determine the reaction forces and moments. Each element has E = 200 GPa. The area moment of inertia are given as I₁ = 1.25 × 105 mm4, and 2 = 4 x 104 mm. Clearly show the elemental stiffness matrices (k) for each element, assembly of k matrices to get global stiffness matrix (K) and application of boundary conditions. Then solve the reduced K matrix to get displacements and reactions 3000 N 150 mm 75 mm 125 mm
3 For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. V = 9 kN, V2 = 9 kN, V3 = 200 mm, and V4 = 1100 mm. ATAT-V3 Provide values at all key points shown in the given shear-force and bending-moment diagrams. X (mm) B A = B = C = D = E= F= P = Q = E * KN * KN * KN × KN KN x KN ✩ kN.mm *kN.mm D 0.00 Reaction force R₁ (left) = In the shear-force and bending-moment diagrams given, +V 0.00 X (mm) 6.3 kN and reaction force R2 (right) = P 11.7 kN. Q 0.00
3. Use the double integration Method and compute the value of EI at midspan for the beam loaded as shown in the figure. R₁ 6 ft 1000 lb 400 lb/ft <-3 ft →→ 4 ft3 ft R₂
The beam AB in the figure supports a load which varies from an intensity of 50 KN per linear meter to 200 KN per meter. 8.2 Determine the location of the resultant load from point A. 200 KN/m 50 KN/m B 6 m
The simply supported beam is subjected to the force F = 700 N and the uniform distributed load with intensity w = 150 N/m. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(r) and M(x). Take a = 0 at point A. 19 F a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 5.2 m 2.6 m 3.12 m Support Reactions The reaction at A is N. The reaction at D is N. Shear Force and Bending Moment Equations In section AB: V(x)= N and M(x)= N-m. In section BC: v(x)- N and M(x)= N-m. In section CD: V(x)- N and M(x)= N-m. A
The dimensions are of the graph are d1 = 7 cm , L1 = 6 m , d2 = 4.2 cm , and L2 = 5 m with applied loads F1 = 130 kN and F2 = 60 kN . The modulus of elasticity is E = 80 GPa . Use the following steps to find the deflection at point D. Point B is halfway between points A and C. What is the reaction force at A? Let a positive reaction force be to the right.
Q2/ Use the unit load method to find the slope and the horizontal displacement of point C on the frame shown below. E=200 GPa, I=200 x 10 mm 5 m B C 4 KN El 2 kN/m 6 m 1.5 EI A-
The figure shown is an I-beam weighing 10 kips/ft which is supported by two columns. If the support at B is roller and C is pinned. Determine the maximum moment of the beam. 10 kips/ft A B A) 0.289 kips-ft (B) 0.268 kips-ft 0.293 kips-ft D 2.81 kips-ft E None of the choices are correct 0.75 ft 1 ft
Question 4 Sketch bending moment diagram for the loading acting on the beam as shown in Figure Q4. From your results, calculate area required for tensile reinforcement using M the formula 4, You may use fyk = 500 MPa and z = 1400 mm. 0.87 fyk 90 kN/m 30 kN/m 200 KN 20 kN/m Danim 100 kNm 2m 5m 3m Figure Q4
The simple beam shown supports the uniformly distributed load with intensity wo = 300 N/m. The span of the beam is 1.2 m. Determine the value of Ely, in N-m³, at midspan. wo 1/2 Ro
The beam shown below is supported by rollers at A and B, and by a pin at C. If EI is constant over the length of the beam, find the reaction forces at A, B, and C. 15 kip AT 6 ft B_ 6 ft 12 ft 3 kip/ft C