12. The inputs A and B in the figure below can be either 0·V·or +10-V. Each diode is silicon with a forward barrier voltage of 0.7-volts. Find for each of the following cases. ↓ (a) A=0 V, B=0.V↓ (b) A=0 V, B = +10 V↓ (c) A =+10-V, B = 0-V↓ (d) A =+10 V, B =+10-V↓ ↓ AO # BO + + 15 V 1.5 ΚΩ

12. The inputs A and B in the figure below can be either 0·V·or +10-V. Each diode is silicon with a forward barrier voltage of 0.7-volts. Find for each of the following cases. ↓ (a) A=0 V, B=0.V↓ (b) A=0 V, B = +10 V↓ (c) A =+10-V, B = 0-V↓ (d) A =+10 V, B =+10-V↓ ↓ AO # BO + + 15 V 1.5 ΚΩ

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
Determine which diodes are forward-biased and which are reverse-biased in the configurations shown in Figure 4. Assuming a 0.7-V drop across each forward-biased diode, determine the output voltage. O+5 V -10 V R DI +s vOK D, -SVOKH D3 +s vOK D4 -5 voK DI -5VOK Dz OVout OVout +5 voK Figure 4.
Given the following circuit with VDD = 5 V, R = 2.6 k, then the current Iis: Use the CVD model for the diode, with VD= 0.65 V. V DD I a. 0.001673 A O b. 0 A O c. 1.673077 A O d. 1.923077 A e. 0.001923 A R + VD -
1. Determine Vpout for the circuit in below and draw Vauts assume the diode is the silicon type. 10 k +10 V-- V. ov R, 100 k IN914 -10 V- 2. What is the output voltage that you would expect to observe across R, circuit of Figure below? Assume that RC is large enough to prevent significant capacitor discharge. +24 V 10 uF RL 10 kn V. ov. IN914 -24 V
Quèstion 15 Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DE 205A iL-DC 220V ams 5OH23 VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above SHOT ON RED MAGIC 5S POWERED BY NUBIA
1. Consider the following circuit, and assume all diodes are ideal. Draw the output to for a triangular input that is given below. ~ Vin R 5 KQ www V1 5V ww D1 R1 5 ΚΩ Vin 10 f -10 D2 ww V2 5V R2 5 KQ Vo
+5 V R₁ = 5 kn VA D₁ D₂ = IDI R, = 5 kΩ Ip2 ID3 D3 VB R3 = 5 k -10 V -5 V Determine VÀ in the multi-diode circuit shown in the figure. Let VD(ON) = 0.7 V for each diode.
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V omsh RL VI-DC20V 0.01 F 0.02 F 0.0167 F None of the above
In the Figure as shown below the current (I) will be equal to: ---- Assume that all diodes are silicon -practical diode model 4 KUZ lovt 32 KSL 2.2 mA O 2.3 mA O 2.4 mA O 1.1 mA O
What is the drop across the diode when it is connected in series to a resistor of 1.8 k2 and a supply voltage of 50 V. The supply voltage causes the diode to be reverse-biased. * O A. 50 V O B. 0.7 V O c. 0.3 V O can not be solve, lack of data
SOLVE STEP BY STEP IN DIGITAL FORMAT Exercise 2 For each of the circuits shown below, determine the current I, and the voltage indicated nodal, V. Use the constant potential drop model. Consider that the diodes are of silicon. a) +5V 5ΚΩ IPZ D >10ΚΩ -5V + V b) +5V 10KN IDZ D -5V 5ΚΩ + V
The D diode used in the diode circuit shown in the figure is a silicon diode. a. Plot the output voltage of the circuit. b. Describe the working principle for each phase in detail R1 10 kN V out +12 V D R2 100 N Vin-15 sin(wt) R3 220 N