1) The power plant is operating on iso-butane as a working fluid. Ob-butane mass flow rate is m = 25kg/s. For the input data see the figure. - Feed water: Mass flow rate of the feed water is 200 kg/s. NOTE: This is an ideal Rankine cycle. In this problem we assume 100% efficiency of the turbine and the pump. The processes are reversible: S1=S2 and S3=S4. Do not change the fluid type! - Use international units to complete calculations The P1 pressure corresponds to the critical point Saturated vapor P1=36.29 bar Boiler W. Qin Turbine Condenser P2=2.26 bar 2 T6=? 6 Cout T5=15C 5 Cooling water Pump 3 saturated liquid

1) The power plant is operating on iso-butane as a working fluid. Ob-butane mass flow rate is m = 25kg/s. For the input data see the figure. - Feed water: Mass flow rate of the feed water is 200 kg/s. NOTE: This is an ideal Rankine cycle. In this problem we assume 100% efficiency of the turbine and the pump. The processes are reversible: S1=S2 and S3=S4. Do not change the fluid type! - Use international units to complete calculations The P1 pressure corresponds to the critical point Saturated vapor P1=36.29 bar Boiler W. Qin Turbine Condenser P2=2.26 bar 2 T6=? 6 Cout T5=15C 5 Cooling water Pump 3 saturated liquid

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 4. Calculate the total turbine work of the cycle.
Problem (1.2) A steam power plant working according to simple Rankine cycle. It has a high pressure of 3 MPa and it maintains 60°C in the condenser. A condensing turbine is used, but the quality should not be lower than 90% at any state in the turbine. Find the cycle efficiency. [reference: Fundamentals of Thermodynamics by Borgnakke & Sonntag prob.11.18,p-460].(Ans.33.2 %).
In an ideal Rankine Cycle, steam at 5 MPaa and 500 0C enters the turbine and expands 300 KPaa. For 110,000 kg/hr of steam, find: a) Ideal power output of the Turbine (kW), b) Power to drive the pump(kW), c) Rate of Heat Added (kW), d) thermal efficiency of cycle and engine, e) steam rate of the cycle and engine, f) Heat Rate SOLVE ALL LETTER PLS : a) Ideal power output of the Turbine (kW), b) Power to drive the pump(kW), c) Rate of Heat Added (kW) d.)thermal efficiency of cycle and engine, e.)steam rate of the cycle and engine in unit (Kg/kw-hr), and f.) Hear Rate in-unit (Kj/kw-hr) PLSS SHOW COMPLETE SOLUTION AND WRITE LEGIBLY ROUND OFF ANSWER TO 4 DECIMAL PLACES . SHOW P-V AND T-S DIAGRAMS PLS PLS REFER TO VALUES OF THE PRESSURE TABLE AND THE SUPERHEATED TABLE IN THE ATTACHMENTS DONT SHOW THE SAME SOLUTION OF OTHERS pls.
Steam enters the turbine 5MPa and 600 and exits adiabatically at 100 kPa. For Actual cycle: turbine efficiency =90%, turbine brake efficiency=84%, generator efficiency=93% Mass flow rate of steam = 15 kg/s Determine the following: For Ideal Rankine Engine Find WT and e SR and HR For Actual Rankine Cycle Find WT’, WB, WK,e’, eB and eK Find SR’, SRB, SRK,HR’, HRB and HRK
3. What are the basic components of Rankine Cycle and draw TS diagrams
The Siemans SST-400 GEO steam turbine is employed in the cycle shown above. Operational information is are shown in the table. you can assume the turbine is adiabatic and you can ignore the KE & PE terms. you can assume that the pump operation is isentropic. the surrounding temperature is 25°C based on the table information: a.Calculate the mass flow of steam [96.5kg/s] b.Find the isentropic efficiency of the turbine [0.836] c.What is the rate of entropy generated (kW/K) in the turbine? [28.26kW/K] d.Calculate the thermal efficiency of the power plant [0.199]
Problem 1: Find and compare the efficiency of the simple ideal Rankine cycle engine operating between20 and 100 deg. C for working fluids of water and Refrigerant 12. Compare the results to the Carnotefficiency.Problem 2: A Rankine cycle operates with steam under the same conditions as in Problem 1. The turbinehas an efficiency of 70 percent, and the pump efficiency is 60 percent. Find the cycle efficiency, andsketch the T-s and h-s diagrams.
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 5. Calculate the thermal efficiency of the cycle
Repeat the previous problem with a closed FWH w/ the same turbine efficiency of 85% but with only one isentropic pump. Determine the cycle efficiency and compare it with the cycle efficiency of an ideal Rankine cycle. Compare it with the cycle efficiency of an ideal Rankine cycle
Problem 3. A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (QH) to the boiler. c. Calculate Wpump- d. Calculate |WNet|- e. Determine the thermal efficiency (n.)
A combined Brayton – Rankine cycle is shown in the figure. Calculate a) all the flow rates shown in the diagram, b) all terms that are required to find the cycle thermal efficiency. Note the relative temperature relations; T6 = To + 5.3 F, T4 = Td + 20 F.
A powerplant operates according to the ideal Rankine cycle shown in the figure. Reheat and regeneration (open feedwater) is employed. What is a) the turbine power output, b) the first law efficiency and c) the second law efficieny for this cycle?