1- A J-Type thermocouple referenced to 80°F has a measured output emf of 2.878 mV. What is the temperature of the measuring junction? 2- Assume that the measured temperature is 250° F, what should be the output voltage if the reference temperature is 90 °F. RK: if the temperature values are not in the table, you have to use interpolation. Response to question 2: The measured output voltage (mV) Select one: a. 2.764 b. 4.769 c. 5.762 O d. 3.768

1- A J-Type thermocouple referenced to 80°F has a measured output emf of 2.878 mV. What is the temperature of the measuring junction? 2- Assume that the measured temperature is 250° F, what should be the output voltage if the reference temperature is 90 °F. RK: if the temperature values are not in the table, you have to use interpolation. Response to question 2: The measured output voltage (mV) Select one: a. 2.764 b. 4.769 c. 5.762 O d. 3.768

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1- A J-Type thermocouple referenced to 80°F has a measured output emf of 2.878 mV. What is the temperature of the measuring junction?
Your factory produces cryogenic refrigerators, and your task is to design a control system for the fridge, but, using the same sensor, you must also supply the end-user with temperature monitoring. The cryogenic freezer is controlled in a tight band around minus 85°C, therefore in controlling the fridge you need to have the most accurate information available regarding the operating range of the fridge (nominally at -85°C, but it can be colder and it can defrost if faulty and reach a maximum ambient temperature of say 50°C to be safe). Due to the economy of RTD sensors, it is decided by management to use a PT100 RTD sensor (range -400°F to 1200°F) with a smart transmitter which needs to be set up correctly to a 4-20mA input on the PLC controlling the fridge. Taking the above conditions into account, the measuring range should be -100°C to 50°C (which should cater for the worst ambient temperature). a) Make sure the RTD is the correct choice b) Set the smart transmitter…
The objective of this question is to give the missing information about the reading of thermocouple type J. The temperatures are in degrees Celsius. The temperature is 100 degrees and the reference is 50. The reading voltage is (mV) Choose... The temperature is 95 and the reference is zero, so the voltage is (mV) Choose... The reference is 30 and the reading voltage is 8.687 mV, The temperature is Choose... + The temperature is 256 degrees and the reference is 75 degrees. The reading voltage is (mV) Choose... +
4. Figure 2 shows a thermocouple circuit J-type used in one temperature measurement system. a) If the reference junction having T2 = 0°C and the output emf is 13.777 mV, what is the temperature of the measuring junction, T1? b) If the circuit produces an emf of 15 mV for T) = 750°C, what is T2? A T В A Measuring environment Potentiometer T2 Figure 2
If the observed voltage given by a thermocouple of type K equals to 72.5 mV then for an amplification factor of 40 the actual voltage is: Select one: a. 0.0018125 mV. b. 0.0018125 V. c. 2.9 mV. d. 0.029 V.
The system given below is to have the following specifications: Ky = 10, 3 = 0.5. Find the value of ki and k; required for the specifications to be met. %3D R(s) 10 C(s) k s (s+1) kfs
2) The following heating system for a room is considered: ATroom = K1 | Qodt, Qo = Qin - Qout Qout = K2AT,0om room Qin = K3(ATrad – ATr00m) where AT is the room temperature and AT is the radiator temperature. What is room rad the stationary room temperature, if the radiator temperature is 50C and if K1 = 104, K2 = 4, and K3 = 1? A. 40°C В. 20°C С. 10°C D. 30°C Е. None of the previous answers are correct.
3. Microfluidic channels will need to be fabricated on a key micro-scale sensor used by aerospace industries. Before running machining tests and analyzing machined quality, preliminary efforts are needed to evaluate selected materials and factors affecting machining process¹. Three material candidates have been selected, including 422SS (stainless steel), IN718 (nickel alloy), and Ti64 (titanium alloy) with their measured tensile properties and equation of true stress-true strain relationship used listed below. Tref25°C. Specifically, three factors will need to be evaluated, including different materials, temperature, and size effect. Please calculate true stress values for true strain ranging between 0-3 for each case listed below. Material A (MPa) & (S-¹) Tm (°C) 870 0.01 1520 422SS (Peyre et al., 2007) IN718 (Kobayashi et al., 2008) Ti64 (Umbrello, 2008) 980 1 1300 782.7 1E-5 1660 Material 422SS (CINDAS, 2011) IN718 (Davis, 1997) Ti64 (Fukuhara and Sanpei, 1993) 0 = X G (GPa) 1+ B…
QUESTION 2 SOALAN 2 Temperature sensing was the initial COVID-19 detection process to isolate people with a temperature, who may have had the virus, from others. Healthcare facilities including hospitals and clinics and other locations frequently used and continue to use non-contact thermal sensing as a precautionary step to prevent the spread of the virus. Based on the statement above, sketch the construction diagram and apply the system for another industrial application and give the reasons.
Find out the error for the given program io = 1.7e-8; % dark saturation current in amperes tc = 27; % cell temperature in degree celsius isc = 250 ; % short circuit current density A/ square meter pin = 820; % solar radiation in w/square meter k =1.381e-23; % Boltzmann's gas constant e= 1.602e-19; % electronic charge t= 273+tc % cell temperature in Kelvin vmax=0.526; % mayi mum voltage in volts imax = (e*vmax)*(isc+io)/(k*t+e*vmax) pmax= vmax*imax efficiency = (pin/pmax)*100 O error in efficiency O no error O Error in pmax O Error in imax O no output
which equation is used if the system underdamped. can you pls share the whole eqn
1.Draw the block diagram of a Temperature measurement system .Also identify the names of the functional elements used in the measurement system.